Tube Step Specs:
Features:
These rugged, all-steel running boards provide a 6-1/2" wide step for entering and exiting your vehicle. Raised steel treads offer superior traction in all weather conditions. Textured black powder coat. Custom mounting kit included.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
Grated steel running boards have an extra-wide stepping surface with raised treads to prevent slipping when entering your truck. Serrated treads provide a rugged look and help keep mud and snow from getting in your cab. Custom mounting kit included.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
Use your foot to lower this spring-loaded step from beneath your vehicle's rear bumper to easily access gear in the bed. The step bolts on without drilling, retracts under your truck for storage and works with your tailgate open or closed.
Installation Notes:
No drilling required for installation
Trekstep can be installed on the driver side only
More Information >Tube Step Specs:
Features:
Grated steel running boards have an extra-wide stepping surface with raised treads to prevent slipping when entering your truck. Serrated treads provide a rugged look and help keep mud and snow from getting in your cab. Custom mounting kit included.
Installation Notes:
No drilling required for installation
More Information >Videos
for Nerf Bars - Running Boards
Help Articles
for Nerf Bars - Running Boards
Expert Answers
for Nerf Bars - Running Boards
On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x…
view full answer...Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire…
view full answer...Based on the information you gave, although I can't help with the axle (other than to state it is a 3,500 lbs axle). Dexter mobile home axles were designed for one time use and…
view full answer...Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
view full answer...