This complete kit includes everything you need to connect your RV's tail, brake, and turn signal lights to your towed car. Diodes prevent damage from electrical feedback. Includes 7-way to 6-way coiled adapter cord and 6-way socket.Features: Complete wiring kit connects your RV's tail, brake, and turn signal lights to your towed car Diodes prevent feedback that can damage your vehicle's electrical components Protected from corrosion by powder-coated aluminum casings 7-Wire to 6-wire adapter cord runs power from RV to towed car Coiled to prevent dragging and tangling Resistant to wear and tear with durable vinyl casing 6-Way socket hardwires to towed car and mounts with included bracket Kit includes: 4 Hy-Power diodes 4-Wire harness 7-Way to 6-way coiled adapter cord 6-Way socket with mounting bracket 1 Butt connector, 1 ring terminal, split loom, and zip ties Made in the USA Specs: Diode max amperage: 85 amps Diode max voltage: 24 volts Coiled cord Max length: 8' Compressed length: 15" Wiring harness length: 27' Notes: A brake light relay (RM-88400 - sold separately) may be required if used with a flat tow brake system.
... Built-in charger pulls just enough power from your vehicle when your trailer is hooked up to make sure your breakaway battery stays charged and ready to go in case a disconnect ever occurs.Features: Makes sure your trailer safely stops if it ever separates from your vehicle Activates your trailer's electric brakes if the trailer disconnects from the tow vehicle Automatically charges battery with the built-in charger when connected to your vehicle Won't overcharge your battery Lets you test battery status with the push of a button Mounts on the outside of your trailer's frame Side-loading case allows easy access to the battery Switch installs on your trailer's frame with self-tapping screws (sold separately) Protects battery from rain and debris with durable, plastic case Lid can be secured with padlock (sold separately) to deter battery theft Wiring diagram is printed on the battery box lid Rubber O-ring in the lid helps keep water out of the box Drain holes in the bottom of the box help with venting and letting condensation drain Kit includes breakaway switch, charger, 5-amp-hour battery, battery box, wiring, and wire loom Specs: Application: single-axle or tandem-axle trailers with electric braking systems Breakaway cable length: 4' Charger amperage: 1 amp Battery: Voltage: 12V Type: Lead-acid Capacity: 5 amp-hours Battery box dimensions: 3-3/4" long x 6" wide x 5" tall 1-Year limited warranty Note: A breakaway system is required by law in most states for trailers that are equipped with electric brakes and have a GTW of at least 3,000 lbs.
... Includes a ball with an easy-to-use handle and ball-bearing locking system, rubber ball hole cover, 2 safety-chain loops, and storage case.Features: Kit works with factory-installed gooseneck hitches on Ford, GM, Chevy, and Nissan Titan XD trucks Pop-in ball fits securely in gooseneck receiver and is easy to insert and remove Built-in-ball-bearing system holds ball in place in receiver Handle provides leverage for operation and a clean way to carry the ball Handle locks in horizontal position to prevent accidental unlatching 2 Safety-chain hookups attach directly to receivers built into gooseneck rails for simple mounting and removal Safety chain anchors accommodate commercially available safety chain hooks (sold separately) Internal and external components are plated or made from stainless steel for corrosion protection Rubber cover keeps dirt and debris out of ball hole when ball is removed Storage case keeps ball, safety chain loops, and rubber cover in good condition when not in use Made in the USA Specs: Gross towing weight: 30,000 lbs Capacity is limited to that of your hitch Ball size: 2-5/16" Limited lifetime warranty
Replaces the toe and skidpad kit for your Thule Pack 'n Pedal RoundTrip Transition bikecase (TH100502). Installs on the outside of your case to protect the bottom of the shell from impactFeatures: Replaces the toe and skidpad kit for your Thule Pack 'n Pedal RoundTrip Transition bikecase (TH100502) Installs on the outside of your case to protect the bottom of the shell from impact
Replaces the top or front handle on your Thule Round Trip Transition hard shell bike travel case.Features: Replaces the top or front handle on your Thule Pack 'n Pedal Round Trip Transition hard shell bike travel case Fits model TH100502 6-3/8" Long Black color Quantity: 1
Replaces 1 strap tab for your Thule RoundTrip Transition bike travel case (100502). Includes installation hardware.Features: Replaces 1 strap tab for your Thule RoundTrip Transition bike travel case (100502) Works with the ratchet catch (sold separately) to secure closure of your case Includes installation hardware Fits: Thule RoundTrip Transition bike travel case: 100502
Want to see your tongue weight at a glance instead of trying to read a tiny dial? Then get ready for this digital scale. We love pretty much everything B&W puts out, so we're really excited to get our hands on this guy too!Protected When You're Done Using It When the job is finished, the scale stores in its weather-tight hard plastic case. It keeps everything protected and easy to grab the next time you want to check tongue weight before a trip. Specs Capacity: Max tongue weight: 4,000 lbs Measurement: Readout: backlit digital display Increment: 5 lbs Accuracy: +/-0.5% Height: Adjustable range: 19-1/2" to 27" Adjustment increment: 1-1/2" Base: Footplate size: 5-1/4" x 8" Power: Battery: 9-volt (included) Compatibility: Coupler size: 2" and larger Storage: Case: weather-tight hard plastic case included
Pre-greased, marine-grade hub is built for trailer idler axles. Fits 3.5K axles with #84 spindles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, cap, lug nuts, and cotter pin included. For 13" to 15" wheels.Features: Marine-grade trailer hub assembly fits idler axles Includes bearings, races, grease seal, grease cap, lug nuts, and cotter pin Pre-greased idler hub is easy to install - no need to pack bearings Lubricated with heavy-duty grease for marine applications (calcium sulfonate, colors may vary) Sturdy iron construction Galvanized finish offers excellent corrosion resistance Ideal for use on a boat or snowmobile trailer Zinc plating on lug nuts, cotter pin, and grease cap helps to limit corrosion Carrying case with handle keeps all the parts in one place Easy to stow on your trailer in case of an emergency Specs: Application: 3,500-lb axles with #84 spindles Wheel size: 13" to 15" Bolt pattern: 5 on 4-1/2" Wheel stud dimensions: 1/2" diameter x 1-7/8" long Grease cap flange diameter: 1.98" Hub flange diameter: 6-1/2" Weight capacity: 1,750 lbs Bearing, Race, and Seal Information Bearings (included) Inner bearing: L68149 (1.378" inner diameter) Outer bearing: L44649 (1.063" inner diameter) Races (included) Inner race: L68111 Outer race: L44610 Grease seal (included): 58846 Inner diameter: 1.719" Outer diameter: 2.565"
Use your Rhino-Rack accessories on your vehicle with factory roof-rack tracks. Locking, Quick Mount legs mount to tracks. Black, Sportz Bar crossbars accommodate clamp-on and channel-mount gear.Features: Adjustable roof-rack lets you carry gear on your vehicle's factory roof-rack tracks 4 Quick Mount legs mount in the channels of tracks to create mounting points for crossbars Durable, glass-reinforced nylon construction Quick-release trigger system allows for easy, tool-free installation Squeeze internal triggers to release legs from bases Slide triggers apart to secure legs to bases Bases remain mounted to tracks Locks in covers let you secure the system to your vehicle Pivoting bases offer 33 degrees of adjustment to help level crossbars Precision-molded inserts cover bases when the legs are removed 2 Sportz Bar black, elliptical crossbars hold ladder racks, conduit cases and other work accessories Bars mount to roof-rack legs using built-in channels on bottoms of bars Lightweight, structural-grade, extruded aluminum construction for strength, durability and maximum carrying capability Built-in C-channel on top of each bar lets you mount Rhino-Rack accessories and carriers Rubber strips in the channels help to cushion load and provide slip resistance Can be cut to accommodate track-mounted accessories and carriers Specs: Weight capacity: 220 lbs Always observe your vehicle's maximum roof load capacity Crossbar dimensions: 54" long x 3-1/2" wide x 1-1/2" tall Leg height: 3" Limited lifetime warranty The bases of these Rhino Rack legs easily mount into Thule or Yakima roof-rack tracks.
Roll out instant shade wherever you stop. The OutLand awning turns your vehicle into a basecamp with quick solo setup and rugged shelter that stands up to sun, wind, and rain. It's ready for overlanders and vanlifers chasing the next great view.Packable and Protected: Telescoping legs stow in the lead rail and awning tucks into a slim, sturdy case. Lightweight, Yet Built Tough: Sleek aluminum case keeps things light but ready for real-world trips. Ready for Your Roof Rack: Universal adapter mounts to Thule and most aftermarket crossbars with ease.
Lead-acid batteries require no maintenance, which is why we love this kit. The built-in charger keeps the battery charged and ready to bring your single-, tandem-, or triple-axle trailer to a complete stop. LED tester lets you check the charge.Features: Makes sure your trailer safely stops if it separates from your vehicle When the pin gets pulled from the switch, a signal is shot back to your trailer brakes to activate Lead-acid battery works great in high temperatures Automatically charges battery with the built-in charger when connected to your vehicle Won't overcharge the battery Lets you test battery status with the push of a button Mounts on the outside of your trailer's frame Side-loading case provides easy access to the battery Switch installs on your trailer's frame with included self-tapping screws Protects battery from rain and debris with durable, plastic case Lid can be secured with padlock (sold separately) to deter battery theft Includes breakaway switch, charger, Lead-acid battery, battery box, wiring, and mounting hardware Department of Transportation (DOT) compliant Specs: Application: single-, tandem-, and triple-axle trailers with electric brakes Battery capacity: Voltage:12V Type: sealed lead-acid Capacity: 5 amp-hours Breakaway cable length: 51" Breakaway switch: Dimensions: 4-3/8" long x 1-1/2" wide Lead wire length: 24" Charger lead wire length: 12" Battery box dimensions: 6" long x 3-3/4" wide x 5" tall Battery case mounting holes: From center to center vertically: 3-1/4" From center to center horizontally: 5-1/2" 1-Year limited warranty Note: A breakaway system is required by law in most states for trailers that are equipped with electric brakes and have a GTW of at least 3,000 lbs.
Simple, push-to-test button lets you check the charge on the battery in this breakaway kit. Complete kit brings your trailer to a safe stop if it separates from your vehicle. Built-in charger automatically charges battery while trailer is connected.Features: Breakaway system activates your trailer's electric brakes if the trailer disconnects from the tow vehicle Brakes receive signal to activate when cable detaches from switch Built-in charger automatically charges battery while connected to tow vehicle Push-to-test button lets you check the battery's state of charge LED lights indicate current battery status Green = fully charged Yellow = charging Red = recharge needed Top-loading case is easy to access from above Durable, plastic case protects the battery from the elements Rubber O-ring seal keeps out moisture 12-Volt, sealed lead-acid battery is rechargeable Wire loom neatly contains and protects wires Switch and battery box install on trailer frame - drilling required Hardware not included Convenient wiring diagram is printed on box Kit includes breakaway switch, 1-amp charger, 5-amp-hour battery, battery box, wiring, and wire loom Specs: Application: single-axle or tandem-axle trailers with electric braking systems Breakaway cable length: 4' Charger amperage: 1 amp Battery: Capacity: 5 amp-hours Voltage: 12V Battery box dimensions: 4-3/4" long x 6" wide x 4-7/8" tall 1-Year limited warranty Note: A breakaway system is required by law in most states for trailers that are equipped with electric brakes and have a GTW of at least 3,000 lbs.
The Thule RideAlong bike seat allows your child to ride behind you on a bike. This reclining seat adjusts as your child grows and is easy to attach and remove using the quick-release bracket. ... Thule RideAlong Bike Seat Grows with Your Child The adjustable seat harness straps and footrests allow you to customize the bike seat's fit for your child.
... Includes a ball with an easy-to-use handle and ball-bearing locking system, rubber ball hole cover, 2 safety-chain loops, and storage case.Features: Kit works with factory-installed gooseneck hitches on Ram trucks Pop-in ball fits securely in gooseneck receiver and is easy to insert and remove Built-in-ball-bearing system holds ball in place in receiver Handle provides leverage for operation and a clean way to carry the ball Handle locks in horizontal position to prevent accidental unlatching 2 Safety-chain hookups attach directly to receivers built into gooseneck rails for simple mounting and removal Safety chain anchors accommodate commercially available safety chain hooks (sold separately) Internal and external components are plated or made from stainless steel for corrosion protection Rubber cover keeps dirt and debris out of ball hole when ball is removed Storage case keeps ball, safety chain loops, and rubber cover in good condition when not in use Made in the USA Specs: Gross towing weight: 30,000 lbs Capacity is limited to that of your hitch Ball size: 2-5/16" Limited lifetime warranty
9" Wide x 72" long x 20-1/2" tall. These sturdy fenders have a flat back to mount flush with your tandem-axle trailer. Aluminum construction is corrosion resistant. Bolt or weld onto your trailer.The old mounting bolts or screws might be stripped or rusted, in which case you'll need to tap them out and buy new hardware. If removing an old, welded-on fender, either carefully chisel it off yourself or take your trailer to a weld shop to have the fender professionally removed.
... Includes a ball with an easy-to-use lever and ball-bearing locking system, rubber ball cover, 2 safety-chain loops, and storage case.Features: Kit works with factory-installed gooseneck hitches on Dodge Rams Pop-in ball fits securely in gooseneck receiver and is easy to insert and remove Lift integrated lever to unlock and remove ball Locks with built-in ball-bearing system Chrome-plated steel is durable and corrosion resistant 2 Safety-chain hookups attach directly to Power Pucks built into gooseneck rails for simple mounting and removal Rubber cover protects ball hole against dirt and debris when ball is removed Storage case keeps ball, safety chain loops, and rubber cover in good condition when not in use Specs: Gross towing weight: 30,000 lbs Capacity is limited to that of your hitch Ball size: 2-5/16" Dimensions of case: 15-3/4" long x 10-3/8" wide x 2-1/2" thick Limited lifetime warranty
10-3/4" Wide x 72" long x 20-1/2" tall. These sturdy fenders each have a flat back to mount flush with your tandem-axle trailer. Rugged, steel construction. Bolt or weld onto your trailer.The old mounting bolts or screws might be stripped or rusted, in which case you'll need to tap them out and buy new hardware. If removing an old, welded-on fender, either carefully chisel it off yourself or take your trailer to a weld shop to have the fender professionally removed.
Everything you need to replace 1 hub on your trailer fits inside of this handy carrying case. Inner bearing (L68149) and race, outer bearing (L44649) and race, and grease seal are all pre-packed in this fully assembled hub with marine-grade grease.Features: Kit lets you replace 1 hub assembly on your trailer Includes bearings, races, grease seal, grease cap, lug nuts, and cotter pin Perfect for storing onboard your trailer in case of an emergency Pre-greased with heavy-duty, marine-grade lubricant (calcium sulfonate, colors may vary) Ideal for boat trailers Strong, cast iron hub is painted black Double-lip grease seal helps keep moisture out and grease in Zinc plating on lug nuts, cotter pin, and grease cap helps to limit corrosion Carrying case with handle keeps all the parts in one place Specs: Application: 3,500-lb axles Maximum wheel diameter: 15" Bolt pattern: 5 on 4-1/2" Wheel studs: 1/2" diameter x 1-7/8" long Hub inner diameter: 1.98" Hub flange outer diameter: 6-1/2" Weight capacity: 1,750 lbs Bearing, Race, and Seal Information Bearings (included) Inner bearing: L68149 (1.378" inner diameter) Outer bearing: L44649 (1.063" inner diameter) Races (included) Inner race: L68111 Outer race: L44610 Grease seal (included): 171255TB (10-19) Inner diameter: 1.719" Outer diameter: 2.565"
We're really impressed with how many features have been packed into a simple door latch. Beyond the keyless access, the app has power-saving modes, locking history, and battery level. This one upgrades your right-handed trailer entry door.Features: RV entry door lock upgrades your right-handed travel trailer, camper, or 5th wheel entry door Standing outside your RV and facing the door, the door hinge is on the right Bluetooth and PIN pad let you unlock the door without keys Optional proximity mode lets you unlock with a single button push Included keys always work in case your batteries have died Advanced features with free Bauer app available for Android and iOS devices Keeps track of locking/unlocking history Displays battery life remaining in lock Change power mode to save battery life - great for long term storage Light and sound indicators warn you if deadbolt fails to lock or when batteries are low Cut-out is the same size as most standard travel trailer locks (3-3/4" tall x 2-3/4" wide) Installs easily with a screwdriver Specs: Overall dimensions: 7-3/4" long x 5-1/4" wide x 3-1/4" deep Weight: 6.35 lbs
Looking for a tough storage solution for your Weigh Safe aluminum drop hitches and accessories? This rugged case is designed to fit both the 180 and Standard Weigh Safe ball mounts. It's a great way to keep everything organized and protected!Features: Carrying case holds and protects the receiver and ball mount attachments from your trailer hitch Easily stow case in your tool box, back seat, or garage Plastic inserts to customize your case Made with bright red plastic
This truck rack works with tonneau covers so you can haul your gear and keep your bed covered. Channels in the uprights and crossbars let you attach a variety of accessories. Adapters attach to your tonneau cover rails with included hardware.The adapters are compatible with the following tonneau covers: Retrax XR Ford Embark LS Pace Edwards UltraGroove (except for 2004 and newer Ford F-150 covers) Yakima Off-Road Rating This truck rack was tested to ensure that it is able to handle regularly adventuring over rough terrain. Yakima extensively tested it with worst-case-scenario lab simulations and real world driving to make sure it exceeded ISO requirements. This rack is built to handle evasive maneuvers, swerving, speed bumps, emergency stops, and whatever else you encounter while off the beaten path.
The Equal-i-zer has a reputation as strong as its American-made steel. We love this hitch's solid build quality and that it helps to proactively stop trailer sway instead of just dampening it after it starts. Ball and shank included.Adjusting the Head Tilt Adding washers adds tension, but it's not a case of "the more the merrier" Stacking washers can be a pain, but you only need to do it once, or if your tongue weight changes Once you've got the hitch ball torqued down, you'll have to adjust the tilt of the head to ensure proper leverage.
Having two motors gives you more leveling control when setting up camp on uneven ground. 74" Bracket height when extended. 3 Universal mount weld stops let you choose how to orient the new legs. Total lift includes 17" of drop leg travel.If not, then you'll need to cut those brackets off and weld on the new ones included with the kit. And, just in case you're curious, the distance between the second and the third weld stops is 5-5/8". What to Know Before Installing Dual-Motor Landing Gear There are some benefits to having legs working independently of each other.
Pre-greased, marine-grade hub is built for trailer idler axles. Fits 2.7K axles with BTR spindles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, cap, lug nuts, and cotter pin included. For wheels up to 14".Features: Marine-grade trailer hub assembly fits idler axles Includes bearings, races, grease seal, grease cap, lug nuts, and cotter pin Pre-greased idler hub is easy to install - no need to pack bearings Lubricated with heavy-duty grease for marine applications (calcium sulfonate, colors may vary) Sturdy iron construction Galvanized finish offers excellent corrosion resistance Ideal for use on a boat or snowmobile trailer Zinc plating on lug nuts, cotter pin, and grease cap helps to limit corrosion Carrying case with handle keeps all the parts in one place Easy to stow on your trailer in case of an emergency Made in the USA Specs: Application: 2,700-lb axles with BTR spindles Wheel size: up to 14" Bolt pattern: 5 on 4-1/2" Wheel stud dimensions: 1/2" diameter x 1-7/8" long Grease cap flange diameter: 1.98" Hub flange diameter: 5-1/2" Weight capacity: 1,350 lbs Bearing, Race, and Seal Information Bearings (included) Inner bearing: L44649 (1.063" inner diameter) Outer bearing: L44649 (1.063" inner diameter) Races (included) Inner race: L44610 Outer race: L44610 Grease seal (included): 34823 Inner diameter: 1.249" Outer diameter: 1.983"
Filters
