Easily raise or lower your boat trailer's bunk board with this slotted, zinc-plated swivel bracket. Bolt the steel piece onto a bolster bracket on your trailer so your bunk tilts toward the hull to keep your boat cradled safely for transport.Features: Swivel bracket tilts your trailer's bunk board when your boat is loaded for transport Allows the bunk to snugly cradle your boat's hull Must be used with a bolster bracket and an additional swivel-and-bolster bracket set (sold separately) for 1 bunk board Slotted design lets you adjust the height of the bracket during installation Bolt-on installation Attaches to bolster bracket on your trailer Mounting hardware not included 11-Gauge, zinc-plated steel resists rust and corrosion Made in the USA Specs: Quantity: 1 swivel bracket Dimensions: 1-3/8" wide x 1-7/8" tall x 3-1/2" long Slot dimensions: 1-1/4" long x 3/8" wide
Dutton-Lainson roller bunkbracket for boat trailers.Features: Roller bunkbracket for mounting Dutton-Lainson standard roller bunks Fits: DL21754 (model 6345) and DL21755 (model 6355) Formed of heavy gauge steel plate TUFFPLATE finish Sold individually 4 Needed to mount a pair of roller bunks Specs: Overall length: 10-3/4" Overall width: 3" Inside width: 2-3/4" Slot length: 7-1/4" Slot width: 7/16" Slots center-to-center: 1-1/4" Top bracket to the start of the slots: 3" Top of bracket to the end of the slots: 10-3/8" Hook: 1-3/4" wide Hole diameter: 3/8" Zinc plated yellow chromate TUFFPLATE finish has three times the corrosion resistance of standard zinc plated trivalent chrome process and 30 percent greater corrosion resistance when compared to powder coated finish.
Boat Trailer Roller BunkBracket for Dutton-Lainson Roller BunksFeatures: Roller bunkbracket, for mounting galvanized Roller Bunks models Fits: DL21740 (model #6387) and DL21741 (model #6388) Sold individually 4 Needed to mount a pair of roller bunks Die-formed of heavy gauge steel plate TUFFPLATE finish Measurement between slotted holes from center to center: 1-1/4" Zinc plated yellow chromate TUFFPLATE finish has three times the corrosion resistance of standard zinc plated trivalent chrome process and 30 percent greater corrosion resistance when compared to powder coated finish.
When bunk boards are not lining up with the hull, these bolster brackets give you room to adjust. Slotted holes let you raise or lower the bunks so the boat sits evenly and loads more smoothly onto the trailer.Features to know about Bolster Brackets for Boat Trailer Bunk Boards These bolster brackets let you mount and fine-tune the height of your trailers bunk boards so the boat sits evenly and loads smoothly.
When bunk boards are not lining up with the hull, these bolster brackets give you room to adjust. Slotted holes let you raise or lower the bunks so the boat sits evenly and loads more smoothly onto the trailer.Features to know about Bolster Brackets for Boat Trailer Bunk Boards These bolster brackets let you mount and fine-tune the height of your trailers bunk boards so the boat sits evenly and loads smoothly.
When bunk boards are not lining up with the hull, these bolster brackets give you room to adjust. Slotted holes let you raise or lower the bunks so the boat sits evenly and loads more smoothly onto the trailer.Features to know about Bolster Brackets for Boat Trailer Bunk Boards These bolster brackets let you mount and fine-tune the height of your trailers bunk boards so the boat sits evenly and loads smoothly.
Uneven tubes can leave scuffs and make loading stressful. This galvanized bracket lines up your 6' and 4' bunks so your pontoon settles square, cutting down on rub marks and standing strong against spray and saltwater.Straightforward Install: Slottedbrackets make placement simple for a tidy, reliable setup. Features to know about Pontoon BunkBrackets for Even, Scuff-Free Support Your pontoon will ride at its best when your bunks carry the tubes evenly.
Heavier pontoons need more contact to ride steady. This wide 6-3/16" galvanized bracket spreads the load across your bunks, keeping tubes square on rough hauls while resisting spray and saltwater season after season.Straightforward Install: Slottedbrackets make placement simple for a tidy, reliable setup. Features to know about Pontoon BunkBrackets for Even, Scuff-Free Support Your pontoon will ride at its best when your bunks carry the tubes evenly.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Slotted mounting hole allows for height adjustment.Features: Light-duty bracket lets you mount a bunk board on your boat trailer Ideal for 2x4 or 2x6 bunk boards on small craft trailers Enables the bunk board to pivot during loading Stabilizes bunk board when 2 brackets are used (additional bracket sold separately) Slotted mounting hole permits as much as 6" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 1 bracket Height: 12-5/8" Mounting slot dimensions: 9-1/8" long x 1/2" wide Bunk board mounting hole diameters: 7/16" Typically mounted upright on a boat trailer's crossmembers, vertical bunkbrackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Slotted mounting hole allows for height adjustment.Features: Light-duty bracket lets you mount a bunk board on your boat trailer Ideal for 2x4 or 2x6 bunk boards on small craft trailers Enables the bunk board to pivot during loading Stabilizes bunk board when 2 brackets are used (additional bracket sold separately) Slotted mounting hole permits as much as 6" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, galvanized steel resists rust and corrosion Made in the USA Specs: Quantity: 1 bracket Height: 9-1/2" Mounting slot dimensions: 6" long x 1/2" wide Bunk board mounting hole diameters: 7/16" Typically mounted upright on a boat trailer's crossmembers, vertical bunkbrackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Mounting slot allows for height adjustment. Dimpled surface keeps bracket from sliding along the trailer frame.Features: Light-duty bracket lets you mount a bunk board on your boat trailer Ideal for 2x4 or 2x6 bunk boards on small craft trailers Enables the bunk board to pivot during loading Stabilizes bunk board when 2 brackets are used (additional bracket sold separately) Dimpled and lanced design keeps bracket from sliding along trailer frame Slotted mounting hole permits as much as 6" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 1 bracket Height: 8-1/2" Mounting slot dimensions: 2-1/2" long x 7/16" wide Spacing between mounting slots: 1/2" Bunk board mounting hole diameters: 7/16" Typically mounted upright on a boat trailer's crossmembers, vertical bunkbrackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back.
Built for mounting a bunk board on your boat trailer, this rust-resistant bunkbracket allows the bunk to pivot when you're loading your boat. Slotted mounting hole lets you adjust the bunk height. ... Features: Light-duty bracket lets you mount a bunk board on your boat trailer Allows your trailer's bunk board to pivot while you load your boat Stabilizes your bunk when 2 brackets are used (additional bracket sold separately) Slotted mounting hole lets you adjust the height during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, zinc-plated steel resists rust and corrosion Made in the USA Specs: Quantity: 1 bracket Dimensions: 2" wide x 11-3/4" tall x 1-1/2" thick
Rust-resistant assemblies let you install 2 roller bunks on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. Dimpled surfaces keep brackets from sliding along the trailer frame.Features: Bolster-and-swivel bracket assemblies allows you to install 2 roller bunks on your boat trailer Dimpled bolster bracket surfaces help prevent the brackets from sliding along the trailer frame Mounting slots permit as much as 3-3/4" of height adjustment during installation Each bolster bracket installs on your boat trailer's frame with a single U-bolt (sold separately) Strong swivel brackets let you tilt the roller bunks Helps you to fit the boat hull snugly onto trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 11" Dimensions of bolster bracket: 10" tall x 2-1/2" wide Mounting slot dimensions: 3-3/4" long x 1/2" wide Spacing between mounting slots: 1/2" Dimensions of swivel bracket: 1-1/4" long x 1-3/4" wide x 2" tall Top flange mounting hole diameter: 7/16" Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
Rub marks, squeaks, or crooked loading? A swivel bolster adds a little pivot so the bunk sits flush to your hull. You set the height, it spreads the boat's contact, and you'll load your boat smoother while protecting it's finish.The slotted hole gives you the wiggle room to dial in the board angle, center the keel, and stop the scuffs. The longer 10" footprint holds the bunk steady, so it doesn't wander after a few launches or a long haul.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Mounting slot allows for height adjustment. Dimpled surface keeps bracket from sliding along the trailer frame.Features: Light-duty bracket lets you mount a bunk board on your boat trailer Ideal for 2x4 or 2x6 bunk boards on small craft trailers Enables the bunk board to pivot during loading Stabilizes bunk board when 2 brackets are used (additional bracket sold separately) Dimpled and lanced design keeps bracket from sliding along trailer frame Slotted mounting hole permits as much as 6" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 1 bracket Height: 9-1/2" Mounting slot dimensions: 6" long x 7/16" wide Bunk board mounting hole diameters: 7/16" Typically mounted upright on a boat trailer's crossmembers, vertical bunkbrackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back.
Light-duty, rust-resistant bracket lets you mount a bunk board on its side and enables the board to pivot. Mounting slot allows for height adjustment. Dimpled surface helps keep bracket from sliding along trailer frame.Features: Light-duty bracket lets you mount a bunk board on your boat trailer Ideal for 2x4 or 2x6 bunk boards on small craft trailers Enables the bunk board to pivot during loading Stabilizes bunk board when 2 brackets are used (additional bracket sold separately) Dimpled and lanced design keeps bracket from sliding along trailer frame Slotted mounting hole permits as much as 4-3/8" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 1 bracket Height: 7-1/2" Inside width: 1-3/4" Mounting slot dimensions: 4-3/8" long x 7/16" wide Bunk board mounting hole diameters: 7/16" Typically mounted upright on a boat trailer's crossmembers, vertical bunkbrackets allow you to mount a bunk board on its skinny side and run the board from the front of the trailer to the back.
This rust-resistant assembly helps support 1 roller bunk on your boat trailer. Swivel bracket enables bunk to tilt when loading a boat. Mounting slots allow for height adjustment. Dimpled surface keeps bracket from sliding along trailer frame.Features: Bolster-and-swivel bracket assembly lets you mount a roller bunk on your boat trailer Stabilizes one end of the bunk - additional bracket assembly (sold separately) required for opposite end of bunk Dimpled bolster bracket surface helps prevent the bracket from sliding along the trailer frame Mounting slots permit as much as 3-3/4" of height adjustment during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) Strong swivel bracket lets you tilt the roller bunk Helps you to fit the boat hull snugly onto trailer during the loading process Hardware is included for attaching the swivel bracket to the bolster bracket 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 1 bracket assembly Overall height: 11" Dimensions of bolster bracket: 10" tall x 2-1/2" wide Mounting slot dimensions: 3-3/4" long x 1/2" wide Spacing between mounting slots: 1/2" Dimensions of swivel bracket: 1-1/4" long x 1-3/4" wide x 2" tall Top flange mounting hole diameter: 7/16" Bolster-and-swivel-bracket assemblies are typically found mounted upright on a boat trailer's crossmembers.
Built for mounting a bunk board on your boat trailer, this rust-resistant bunkbracket allows the bunk to pivot when you're loading your boat. Slotted mounting hole lets you adjust the bunk height. ... Features: Light-duty bracket lets you mount a bunk board on your boat trailer Allows your trailer's bunk board to pivot while you load your boat Stabilizes your bunk when 2 brackets are used (additional bracket sold separately) Slotted mounting hole lets you adjust the height during installation Bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) 11-Gauge, zinc-plated steel resists rust and corrosion Made in the USA Specs: Quantity: 1 bracket Dimensions: 2" wide x 9-7/8" tall x 1-1/2" thick
Rub marks, squeaks, or crooked loading? A swivel bolster lets you pivot your bunk so it sits flush to your hull. You set the height, it spreads the boat's contact, and you'll load your boat smoother while protecting it's finish.Features to know about Centered, Scuff-Free Loading When a boat loads crooked or rubs the same spot every trip, it's usually a bunk alignment issue, not the hull. Swivel bolster brackets let you adjust your bunk boards to where they should be, so the hull sits right and loading feels smooth.
Rub marks, squeaks, or crooked loading? A swivel bolster lets you pivot your bunk so it sits flush to your hull. You set the height, it spreads the boat's contact, and you'll load your boat smoother while protecting it's finish.Features to know about Centered, Scuff-Free Loading Swivel bolster brackets let you adjust your bunk boards to where they should be, so the hull sits right and loading feels smooth. The 2-3/4" vertical slot gives you the wiggle room to dial in bunk height for your boat, and the non-slip dimples bite into the board to prevent movement and boost load capacity.
If your bunkbrackets are rusted, bent, cracked, or no longer keeping your bunks aligned and tight, it's time for new ones. This will make sure your boat sits square, loads smoothly, and you're not risking hull damage or a failed support.Highlights Get Your Boat Hull to Sit Right: The 2-3/4" vertical slot lets you dial in bunk height so the boat centers on your trailer. Stop the Squeaks: Non-slip dimples and a 10" base spread the load and stop bunk creep, so boards do not dig in or squeak.
If your bunkbrackets are rusted, bent, cracked, or no longer keeping your bunks aligned and tight, it's time for new ones. This will make sure your boat sits square, loads smoothly, and you're not risking hull damage or a failed support.Highlights Get Your Boat Hull to Sit Right: The 2-3/4" vertical slot lets you dial in bunk height so the boat centers on your trailer. Stop the Squeaks: Non-slip dimples and a 12" base spread the load and stop bunk creep, so boards don't dig in or squeak.
If your bunkbrackets are rusted, bent, cracked, or no longer keeping your bunks aligned and tight, it's time for new ones. This will make sure your boat sits square, loads smoothly, and you're not risking hull damage or a failed support.Highlights Get Your Boat Hull to Sit Right: The 2-3/4" vertical slot lets you dial in bunk height so the boat centers on your trailer. Stop the Squeaks: Non-slip dimples and an 8" base spread the load and stop bunk creep, so boards don't dig in or squeak.
... Swivel brackets enable bunks to tilt when loading a boat.Features: Bolster-and-swivel-bracket assemblies allow you to install 2 bunk boards on your boat trailer Extra-sturdy connection to trailer frame ensures support for the bunk boards Each bolster bracket attaches with 2 U-bolts (sold separately), as opposed to a standard bracket that attaches with 1 U-bolt Mounting slots permit as much as 3" of height adjustment during installation Bolster brackets install vertically on your boat trailer's frame Heavy-duty swivel brackets let you tilt the bunk boards Helps you to fit the boat hull snugly onto your trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 3 Bolt holes for a strong, sturdy connection to the bunk board 7-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 12-1/4" Dimensions of bolster bracket: 11-3/4" tall x 4" wide Mounting slot dimensions: 3" long x 1/2" wide Horizontal spacing between slots: 1-1/4" Horizontal spacing between slots: 1/2" Dimensions of swivel bracket: 3-1/2" long x 1-1/2" wide x 2" tall Flange mounting hole diameters: 3/8" Flange mounting hole spacing: 2-1/2" apart on center 1-1/4" Between each of the 3 holes Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
Filters
