!Liberty Travel Trailer  x   >   200  x   >   1979  x   >  

79 cj5. Can I run half doors without a soft top on? | The Bestop Soft Lower Half Doors part # B5302701 that you referenced do not require any top to be on your Jeep. |

Hello. I am looking for a vinyl/tonneau cover for a 79 Chevy short wide. I guess I could modify a long bed. But... Looking for one with Velcro only. No snap on buttons.. Than you.. | Hello Gerald. Your 1979 Chevy has a 6 foot bed correct?...

Just looking for tool box options that fit. | The average bedrail height for Ford F-150's is approximately 21", so going off of that measurement and allowing for your Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover # 311-FEF1290...

can you make a trailer hitch for my 1979 Plymouth volare? all I will be towing is my sea-doo. | We don't have a custom fit trailer hitch receiver for your 1979 Plymouth Volare. We are a retailer and not a hitch manufacturer, so we don't make...

I need a receiver hitch for my 1979 Chevrolet Scottsdale k10. The distance from the bottom of the frame to the bottom of the step bumper is 5 inches. Can you tell me what models will work? The frame width is 34inch outside to outside. | Based...

I want to put this cover on my 1979 F100 Short bed Fleet side pickup truck. The dimension of my truck bed is 80 3/8 inches long and 65 1/4 inches wide. Will this bed fit my truck? | The Access TonnoSport Soft, Roll-Up Tonneau Cover # A22010029...

Will these doors fit my 1979 CJ7? | The correct Black Denim Bestop 2-Piece Soft Doors for your 1979 Jeep CJ-7 can be found as part # B5177815 on our site. Since this comes as 2 pieces you can take the top piece off if you'd like as opposed to...

I am looking for a class IV universal trailer hitch. I Have a 1979 Jeep Wagoneer that I want to install it on. Do you sell them? | We have the part # 41990 which is the main crosstube of a Class V hitch that you can use the part # 4916 for a...

What other Chevy models will this hitch fit? Monte Carlo, Chevelle, etc.? | The Draw Tite hitch # 75082 does not fit any Chevy models actually. It fits the following: 1994 - 2010 Mazda B Series Pickup 1983 - 2012 Ford Ranger 1986 - 1989 Ford...

Can you tell me the backspacing of this wheel? | For 6" wide wheels that have a zero offset the backspacing is about 3-1/2". Since the Dexstar Conventional Steel Wheel # AM20766 that you referenced has a +0.5" offset that means that the backspacing...

Do you know if it has that pin in middle like the motor to fit the split shaft. I don’t have the part numbers on me. | Yes, the Replacement Manual Hand Crank for Ultra-Fab Twin II Stabilizer # UF39-84-1641 has the pin in the socket on the end...

Can this fan be used on a fan clutch in a 1979 Pontiac Trans Am olds 403 v-8? | The Derale fan part # D17418 that you referenced was not designed to attach to a fan clutch. For a similar size fan that is and the correct direction for your 1979...

I need a class III hitch to fit my truck. 1979 f250 4x4. What do you have that will bolt up? | I recommend the Curt Class III Trailer Hitch Receiver # 13028 for your 1979 Ford F-250. This hitch will fit either the standard bumper or the deep...

I know that you cannot recommend this wheel for a vehicle but will this wheel Item # AM20504 fit on a 1979 Ford F-150, custom super cab pickup? Its a 2 wheel drive truck with a stock 5 bolt pattern wheel. I like these wheels and would like...

I have an older Trail Boss hitch and rails. What I need to know is this the kit I would need to mount it into my Ford F150 Custom. And also if this is all I would need. Thank you for any help info. | For your 1979 Ford F-150 and Trail Boss 5th...

What is the distance center to center from the top hole to bottom? Thanks | The top mounting hole measured center to center to the bottom mounting hole is 18". The overall length of the arm is 19 1/4". The mirrors are going to be a bolt on...

I need to order a receiver hitch for my 1979 ford f250. Do I measure the frame width from outside to outside, or inside to inside, or center to center ? I want to make sure I order the correct one. Thanks | When measuring the frame width on...

Can I Get A Car Ramp Without A Hook On The End? | The only ramps we offer without hooks that can load your 1979 Chevrolet Corvette that are close to 12' are the Race Ramps Trailer Loading Assist Ramps - 11" Lift - 136-7/8" Long - Qty 2, part...

I have a 1979 Ford F150. I need a Westin Fey diamond step bumper part number 71000. What installation kit do I need and do you have the bumper in stock for immediate shipping? | Westin has a Fey bumper and hardware kit that fits your 1979...

Do you have a rear bumper for this truck ? Will a # 61001 fit. | The Westin Fey Surestep Rear Bumper # 61001 referenced in your question may fit your 1979 Chevy Luv but you will need to make or have somebody fabricate mounting brackets in order...

Received my order for a Blue Ox BXW0756 When ing the shank into the receiver the brace strikes the bumper at at least 1inch before getting to the point that the pin can be ed into the receiver. I need a shank where there is at least 5 inches...

We are going to flat tow a 1979 CJ5 Jeep behind our motor home. What tow bar do you suggest. | In order to be able to tow your 1979 Jeep CJ-5, you will need to install base plates which the tow bar will attach to. We do not carry any specific...

Looking at ultragroove and explore, they seem to be compatible with the same Thule and Yakima gear. Whats the difference between the two besides load rating? I have a 76 F-150 so the jackrabbit/explorer is my best option, but Id like to use...

Does this fit or do you have a trailer hitch that will fit a 1979 Buick Electra Estate Wagon | There is only one trailer hitch that fits the 1979 Buick Estate Wagon. It is # C12009. But this is a Class II hitch with a 1-1/4 inch receiver rated...