Will a Wheel with a 5 on 4-1/2 inch Bolt Pattern fit on Dexter Trailer Hub 8-248-50UC1-EZ
Will this hub work with AM3H490 Kenda 205/65-10 Bias Trailer Tire with 10inch Galvanized Wheel - 5 on 4-1/2 - Load Range E | A wheel like what you described with a 5 on 4-1/2 inch bolt pattern would fit right up to the Trailer Hub Assembly...
Which Ball Mount Can be Used With Curt Trailer Hitch # 14053 for a 1998 Ford Econoline 250
I have a 98 ford 250 Econoline Van with a factory step down bumper. What length ball mount do I need with this hitch | The recommended ball mount for Curt Trailer Hitch # 14053 for the 1998 Ford Econoline Van is # 2923. However, for your specific...
Recommended Trailer Hitch Receiver For 1993 Ford Van
I called and was told you dont have a hitch for my application. But seems there has to be, maybe based on measurements, not vehicle info. I have a 93 Ford E350 16 passanger bus. Door sticker says incomplete chassis. The inside of the frame...
Trailer Grease Seal Recommendation for Inner Diameter 1.7 inch and Outer Diameter 2.33 inch
Hello I have 2 boat trailer axle related questions... I am looking for 2 wheel bearing seals- ID 1.710 OD 2.33 .... and 2 standard grease or dust caps - OD 1.810..... I found a Hadco dust Cap on another site, Hadco # 1.810 Can you...
Rear Anti-Sway Bar for a 1996 Dodge Roadtrek
Hello, I am trying to find a rear sway bar for my 1996 dodge Roadtrek 190. I am seeing that many of the available sway bars may not fit my van due to the undermount water and storage tanks. I see that you all suggest the RAS a lot. Would...
Spare Tire Carrier for a Front Mounted Trailer Hitch
Hi, I have a Ford E-350 based Class C RV and right now I have my spare 16inch dually wheel/tire mounted on the front, which I accomplished using a Draw-Tite front hitch and Draw Tite 6715 Hitch Mounted Spare Tire Carrier plus a J pin stabilizer...
Installation of the Prodigy On a 96 Winnebago p-30 chev.
my winnebago has a factory 7-prong trailer connector. i believe it already has a wiring harness up to the dash. how do i check for it and do you have instructions for it. | Installation of the Tekonsha Prodigy should be fairly easy with the...
Recommendations For Trailer Hitch On A 1998 Ford E-450 RV Cutaway
Im looking for a hitch for a 98 Ford E-450 RV Cutaway. Have anything that will fit? Thanks | To find a trailer hitch that will work well on your Cutaway I recommend a weld-on trailer hitch. You will need to take a measurement to make sure...
Extendable Towing Mirror Recommendation for a 1996 Ford Club Van
I have a 1996 ford club van with manual mirror and would like to get extendable mirror. | The style of mirror you have on your 1996 Ford Van is not one that has slip-on mirrors that are confirmed as fits, but I do have a solution if you want...
What Circuit on 1996 Ford Van for Charging Trailer Battery
I have an 1996 conversion van. years ago I thought the peope hooked up the charging wire from my van. They did not. I found a 4 wire bundle at my rear bumper with a hotwire that has 14.2 volts with the engine running. How can I hook that wire...
Best Rear Suspension Enhancement for 1996 Winnebago Minnie Class C
I have a 1996 Winnebago Minie Class C motorhome built on Ford E-350 Econoline chassis with leaf springs and dualies. GVWR is 10,000 lbs. Id like to minimize jounce. No current problems with sway or sagging rear loading. I do not usually tow...
Is 12 Volt Accessory Circuit Needed on Trailer Wiring
I own a 1998 Ford E-250. It has a factory installed 7-way plug at the rear which was damaged and I am attempting to replace. I tested the leads and I have continuity on all leads except for the 12v power lead. Should the 12v lead have power...
Draw-Tite # 5350 Recommendation for a 1996 Shasta 280 Motor Home
I bought a 1996 28foot Shasta Motor Home it had a draw tite hitch that attached to the side of the frame with 3 1/2inch bolts. The problem was that there was an extension left in that rusted tight and had extra holes drilled in it making it...
Front Hitch Recommendation for a 1998 Winnebago Built on Ford E450 Cutaway Chassis
Draw-tite model 65001 front hitch, will it fit my 1998 Ford 450 with Winnebago coach? | The Draw Tite Front Mount Hitch part # 65001 that you referenced has been confirmed to fit your 1998 Winnebago coach that is built on a E-450 cutaway chassis...
Distance from Center of Hitch Pin Hole to the Tray of the Curt Cargo Carrier # C18100 Folded Down
What is the distance from center of hitch pin hole to closest edge of carrier when carrier is NOT folded up? | The distance from the center of the hitch pin hole to the nearest portion of the Curt Cargo Carrier # C18100 when folded down is 8...
Do Torklift Glowsteps Require Tools to Remove/Install from Mounting Bracket
Hi Does the step require tools to remove? The brophy step snaps off and on. Thanks | The install and removal of the step portion of the GlowSteps part # TLA7802 is pretty easy and does not require the use of any tools. Basically you just pull...
What Is The Width Of The Thule Telescoping Ladder # TH301404?
What is the width of the ladder? | According to Thule their Telescoping Ladder # TH301404 is 25" wide. |
How to Wire the Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent
the c terminal is for the switchboard, which is what? the m terminal is what the motor goes to. The b is terminal is for fuse and power supply? What if I do not have switchboard wire | For the Replacement 3-Speed Switch for Fan-Tastic Vent...
Location of Brake Controller Installation Port on 1996 Ford E350 Van
Ive searched high and low for the plug under the dash to plug in my brake controller but cannot find one. Do you have any feedback? I have a 1996 Ford Van 350 | The brake control connector on an E-series van is located under the left side of...
Steering Stabilizer that Fits 1996 Ford E-350 Born Free RV
Looking for a front end steering stabilizer for my 1996 Ford E350, V10 Born Free RV . Can you help me? Thanks, | The Roadmaster Exact Center part # RM47MR is a confirmed fit for your 1996 Ford E-350 Born Free RV. This will replace your OEM...
Inside Mounting Dimensions of Surestep Bumper 21002
Hi Im looking at buying a Surestep #21002. My question is, what are the inside dimensions across of the mounting part see your pic of the Surestep # 21002 and are these dimensions of the 21007 the same? Ive included a pic of my 1996 Dodge...
Replacement Hardware Kit for 1996 Dodge Van Draw-Tite Max-E-Loader Hitch Receiver
Do you have a hardware kit for a Draw-Tite 41533? | To get replacement hardware for the Draw-Tite Max-E-Loader 41533 you need to order part # RHK on our site and input the hitch part number. Once you place your order we'll get all of the hardware...
Which Classic Accessories Boat Cover Will Fit 1974 Tahiti 18 Foot Boat With Outboard Motor
I have a 1974 18 foot TAHITI boat with 115 mercury outboard motor. I live in utah, with the boat being parked outside, what boat cover would you recommend. thank you | I contacted our representative at Classic Accessories and he recommend...
Does Draw Tite Front Hitch # 65001 Fit 1996 Born Free President RV
Will this fit my 96 Born free president model RV? | Yes, the Draw Tite front hitch part # 65001 does fit your 1996 Born Free President RV built on a Ford Cutaway chassis. |
Filter Your Search
Contact and Help