1998  x   >   !Mighty Cord  x   >   !1995  x   >   Suburban  x   >  

is this hub threaded so i can get a threaded bearing buddy that wont pop out easy or be stolen easily | The hub is not threaded. Bearing Buddies are meant to be driven in with a mallet or hammer, not screwed in. As long as the outside diameter...

I am interested in purchasing two prodigy 3 for two of my 1998 chevy k3500. Question 1, will they work Qusetion 2, will I need to purchase a wiring loom and if so, which one? Thanks | Yes, the Prodigy P3 # 90195 would work extremely well in...

Needing to completely rewire 18 foot auto transport dual axle 7 blade with brake on one axle... Is it best to use a box or just 7 blade connector and straight wiring by the foot....and what do I need for both?....just about to lay all new flooring...rewire...

do you have these in the 1/2 diameter ,y ubolts or 1/2 would 9/16 be better or to small in strength | You will want to choose the diameter size of U-Bolts you need by the axle type (round, square) and the axle diameter. The Redline 2 Inch Square...

Im going nuts trying to find the 1/2inch X 1 1/2inch bolts for the Frame Brackets for the Reese Dual Cam Control. You offer the Rivet Nuts separately, you offer the Frame Brackets separately......but darned if can find the bolts for both of...

need to replace all the vent covers for a cougar 246e travel trailer what parts do i need | The vast majority of trailer roof vents are the 14 x 14-inch size. Since trailer makers don't often maintain detailed records about items like roof vents...

I installed the Tekonsha P3 brake controller about a year about and have had no problems until now. I recently got in to move the my truck and trailer and had the open ground error message. The weird thing is that when i push the brake pedal...

Looking for options for my early 1999 k1500 suburban. I have a blue ox 7365 tow bar with the pins that screw into base plates. I need base plates. My tow hooks bolt to the bottom of the frame. I’m a good diy guy with tools and welder. Do you...

I need to fit a actuator for my tri axle boat trailer with 6 disc brakes and a controller for my 1998 Surburban could you please advise!! the trailer and boat weighs aty about 8000 lbs. | When using an electric over hydraulic brake actuator,...

Is this all metal or is it plastic where it slides into the hitch? | The Green Bay Packers 2" NFL Trailer Hitch Receiver Cover # HCC2019 that you referenced is made entirely of ABS plastic. For a similar all metal cover you would want the part...

I have a little 15 ft Fleetwood travel trailer and pulling with a 1998 Suburban C1500. What is the best hitch for this? | We have a couple of trailer hitches that are designed to fit your 1998 Suburban. I recommend the Curt Trailer Hitch,...

I have a 98 chevy suburban the mirror has a 4 pin connector nad the truck has a 8 pin connector. Will they plug in? or is there a jumper as stated in step 5 | The CIPA Magna Custom Extendable Towing Mirrors - Electric 70000 that fit your 1998...

I have a 1998 K1500 Sub 4x4 and it has the heavy duty tow package. I would like to know if I need an adaptor wire harness to plug a brake controller under the dash or how do I install a brake conroller? Thanks! | GM did not start using the...

is it possible to get just the mounting brackets for F2101 as I was given the air bags off of another vehicle. I saw in the reviews that you did it for somebody else. | Yes, you can buy the brackets and the hardware for part #F2101, the Firestone...

I want to tow my 1998 GMC Suburban 1500 4x4 but there is no make/model/year for this vehicle in your charts. Can I use the chart referencing the chevy/suburban 1500/1998 to choose its equivalent base plate. Would also like to have your experienced...

Im planning to pull a boat and trailer weighing 6500 lbs with approximately 10 percent on the hitch. Im not planning to do a lot of backing up, but will need to at a launch ramp and to back the boat into my driveway. The trailer is already set...

Using a battery isolator to charge a trailer battery. Can the charging wire #4 gauge be also used to power a small winch? 30 amp. Without towing a trailer | Yes, you could use the Pollak 2-Pole Trailer Wiring Connector and a 4 gauge wire to...

Hi Guys, I have a 1998 Chevy Suburban with a class 3 reese hitch: 2 inch receiver: will the Carpod fold down carrier work on my particular vehicle? Im wanting to purchase this unit if it will fit. thanks | To determine if the Carpod Walled Cargo...

Hello, I have a Tekionsha P3 and I am getting the message OUTPUT SHORTED. Does this mean the blue wire that goes from the controller to the hitch is grounding somewhere, or can it be on the trailer side? It shows this message even when the...

WHAT SIZE and CASE STRENGTH BOLTS DO YOU RECOMMEND. WILL BOLT NEW COUPLER ON. THIS TITAN SURGE COUPLER WILL REPLACE AN OLD WELDED ON SURGE COUPLER. THE OLD ONE LOOKED LIKE AN ATWOOD and WAS WELDED ON. OLD COUPLER WAS CUT and GROUND-OFF. REMAINING...

Hi, looking over my 98 GMC Suburban I see that one of the two power posts on the fuse block already has a connection of some sort secured there. The kit instructs attaching one wire to each of the fuse block posts. I was wondering if it is...

Hi, I just ordered part #ETBC7 for my 1998 Suburban. I noticed there is an install video for a 93 and a 99 Suburban. Is there one I should follow more closely for my 98? I noticed the 93 video just plugs existing 4 plug connector into new...

I have a 1998 GMC C2500 Suburban, I have a blown trailer fuse. It’s not on the legend of either fuses blocks. I have read that its along the cowling in the engine compartment but I cant seem to locate it. Any help would be greatly appreciated....

I want to install a trailer wiring kit onto my 1998 Suburban. It doesnt have any wires that I can find in place for this. What kit can I use? Id perfer to have it set up like the new trucks round connecter. Any help you could provide would be...