Options to Replace Calkins Double Roller Assembly on Boat Trailer
Hi I am looking for calkins boat trailer Double Roller assembly for my Keel and bow rollers. Cant find them online or any store and mfg is out of business. DO you guys know or have this part or something that can be used as a replacement? Thanks...
What is the Exact Length of the 12 Inch Yates Side Guide Roller # YR12243-5
What is the actual length of this 12inch roller, #YR12243-5, down to 1/16th of an inch? Will it work inside a 12inch bracket, #408300, without binding? | I went out to the warehouse and measured a few of the Yates Side Guide Rollers # YR12243-5....
Need a y block stop for tri hull what do recommend or which one do you recommend | For a Y-style bow stop for your tri-hull boat go with either the Yates Y-Style Bow Stop for Boat Trailer - 6-1/2" Span # YR6Y33-4 or 7" Span # YR7Y44-4. These...
Replacement for a 4-1/2" Long Keel Roller on a Boat Trailer
Im looking for 4.5 inch long rubber keel roller for my boat trailer. I see several 4 inch and 5 inch but I need 4.5 inches. Is this something you can source? Thanks | The 4-1/2" keel roller is a size commonly found in Australia. You might consider...
Roller Shaft Replacement for 10 Inch Yates Roller
I am replacing the roller - see attached photo. It is a 10 inch Yates roller. I ordered all the parts except for the roller shaft - which model do I order to include the end caps? | For the Yates Keel Roller for Boat Trailers - Heavy-Duty Rubber...
Removing a Retaining Ring from a Wobble Roller
how to remove old retainer ring on wobble rollers | Probably the easiest way to remove a retainer ring, such as # CE10981, to replace a wobble roller is to grip one end with some vise grips and the other end with some pliers. Then twist in opposite...
Center Diameter for 12" Long x 3-3/4" Diameter Yates Keel Roller for Boat Trailers
I have a 1989 Larson All-American boat and trailer. I need to replace the rear keel roller. The current roller is 12 inches long. The outside diameter is 3 3/4 inch, and the middle diameter is 2.83 inches. There is no channel at the middle...
How Many Bow Rollers Does a Trailer Usually Have
How many do I need for a 12 ft. alum boat? How far apart should they be spaced? | Normally a trailer only uses one bow roller like the part # YR450BLK that you referenced up near the front of the trailer where the boat rests against the front...
Solution for 5/8 inch Keel Roller that Is Slightly to Large for Boat Trailer Shaft
I recently purchased 4 of the Yates YR-5213-5 keel rollers. The rollers that I replaced had a hard plastic sleeve. I just assumed the new rollers would come with the sleeves but they did not. I was able to remove the sleeves from 3 of the old...
Recommended Replacement Wobble Roller Parts for Venture Boat Trailer
Hello, Great descriptions on your website, but I still need some help. Please see the attached picture. I have the missing roller and one washer, but need a new clip and the black rubber thing. The washers inside diameter is 1-1/8inch but...
3 inch Boat Roller Availability
I have a trailer with the 3inch rollers. Do u stock anything like that? I see u have the 8inch ones i need. | We sell 3 inch bow rollers like the part # YR300Y that is designed to attach to a 1/4 inch stud. Or for a 3-3/4 inch one you would...
Inner and Outer Diameter of the Yates Spool Roller for Boat Trailers
Hello, for part # yr8302-4p, what is the inner OD, the narrow part of the roller? Thank you, Peter | Hey Peter, I actually went out to the warehouse and measured the Yates Spool Roller for Boat Trailers # YR8302-4P and measured 51 mm for the...
Parts Found In Pictures for CE Smith Bow Roller Bracket # CE31005PG
What is the winch pictured in the CE31005PG picture number 6? In other answers you say winch DL16001 is compatible, and also that MT70176 is compatible, but neither is the winch in the picture, and neither is quite what Im looking for. | The...
Correct Roller Shaft for CE Smith Side Guide Roller for Boat Trailers
I cant seem to find an appropriate length shaft for this 9 inch roller on your website. They are all either several inches too long or too short. Please send part info for a compatible shaft. | The reason that you are having difficulty finding...
Distance from Mounting Hole to Bottom of Yates Y-Style Bow Stop for Boat Trailers # YR4Y22-3
Im looking at your YR4Y22-3 2X2 What is the measurement from the bottom of the stop to the 3/8th hole? The bottom meaning. The bottom of the Y | Yates Y-Style Bow Stop for Boat Trailers # YR4Y22-3 measures approximately 1/2 inch from the...
Parts Needed to Replace 12 x 2-1/2 Inch Rollers on Boat Trailer
Hello, I am looking at replacing the side guide rollers on my trailer. The current rollers are 12x 2-1/2inch w/ 1/2inch Shaft. I found the correct replacement roller on your site from Yates along with a top cap but I cannot find the right length...
Replacement Keel Roller Recommendation to Replace 7-3/4 Inch Roller
The bracket on my boat trailer keel roller is 7 3/4 inches wide. I see a lot of 8 inch wide rollers but if they are 8 or over will not fit. What is your recommendation? | You would need to replace the bracket with part # CE10303G and then...
What is the Closest Bow Roller Assembly Available for a 3-1/2" Wide Bracket
I need a bow roller assembly that will fit a 3-1/2 wide bracket. Do you have one? | No, we do not have a bow roller assembly that fits a 3-1/2" wide bracket. The closest that we have are for 3" or 4" brackets. 3" - Bow Roller Assembly # YR300Y-325Y 4" -...
V Stop for Sail Boat Trailer with 1/2" Bolt
My sailboat trailer King manufacturing has a black bow stantion roller. I want to switch out to a 3 inch V stop that is non marring. The sailboat has a fine bow entry. I’m looking for advice for a good V stop. My bolt hole is 1/2 inch. Can...
Non Marking Bow Roller for River Boat
Hello, which bow roller would you recommend for a 20 aluminum river boat? The one that I currently have is blue and very soft. | I like the non-marking rollers like the 4 inch bow roller part # TR450B-400B which fits a 1/2 inch shaft or the...
Boat Trailer Wobble Rollers for 1 Inch Diameter Shaft
Do you have 4 pack yellow rollers available to fit 1inch shaft | Judging by the diameter of the shaft the roller fits on, I'm assuming you're needing a wobble roller. We offer two different wobble rollers that will fit a 1 inch shaft, part...
Availability of Bow Roller Kit that Includes End Bow Bells
Do these Bow Bell come in pairs or individually if I am buying the bow roller | The Yates Bow Bell # YR400BLK that you referenced comes individually in that part number. For a kit that includes the 4 Inch roller, 2 end bells, and corrosion-resistant...
Diameter of Center Section of Yates Keel Roller part # YR800B
Looking at Yates part tpr 8inch long keel roller from diagram I see the length is 8inch and that the end of roller is 3 1/2 inch diameter what I need to know is the middle diameter. Thanks for your help . | The center section of the # YR800Y...
How To Replace a Knot Autoflex Winch and Bow Roller Assembly On a Boat Trailer
I have a Knot Autoflex. I want to use the FW20000301 What do I need to easily replace? Thanks! | I do have a solution for you but we don't offer any integrated winch and bow roller setups like the Knot Autoflex. Therefore, you'd have to purchase...
Filter Your Search
Contact and Help