GMC  x   >   !scion  x   >   Kenworth  x   >   John Deere  x   >  

Would your King Pin Hitch work on a Holland FW35 series 5th wheel? And if so, what wire harness do I need to use to connect to my 7 way plug on my 2007 Kenworth T800? | I do see your Holland FW35 is designed to fit a 2" kingpin like the one...

I have a 2016 JD 825i and want to install quick disconnects at the front and rear for my 4500 lb superwinch. Do you sell a kit that has all of the wiring that I would need? Thanks | In order to install a quick connect winch wiring harness on...

I have a flatbed trailer with electric over hydraulic brakes. I tow this with either my 2015 chevy 3500 or my 1999 kenworth t2000. I need a something so it will activate my brake lights on the trailer and turn on the hydraulic pump on when the...

Have an upfitted Kenworth T270 What would be the proper trailer plug wiring schematic for a 2020-21 Kenworth T270? The PLUG wires would are Lt Blue, Orange, Brown, Green, Yellow, White Brake does not work. Turn, Running, etc work Obviously,...

2007 kenworth t300..hitchs is 34inch 16 | Since you have a 34 inch wide frame, we may have something that could work with a bit of fabrication on your part. 34 inch wide frames (measured from outside to outside) is a very common frame width...

... Hey Guys! Can i just purchase the rear wheel liners? Cheers | The Wheel Liners confirmed to fit your 1987 John Deere Motorhome are only available in the complete front and rear package # NA7195D0. You may also want the Wheel Masters Tire...

I have an old fire truck that I’m putting a fifth wheel hitch on, the frame measures 34 1/2” outside to outside, which do you recommend? | Putting a fifth wheel hitch in a truck like yours gets pretty difficult since the distance from the rear...

the brake lights are on all the time, the signal wire appears to be a ground coming from my brake switch. is that normal for the signal wire to be an interrupted ground? is my converter bad? | It's possible that the converter box on your Curt...

I have a single rear axle 1994 Kenworth t 600 that I want to install timbren system on, I talked to timbren and they suggested I go through a dealer so I could get 1/2 a kit. the part number is kwrag100 but I only need 2 bumps and brackets....

My T800 has a front axle rating of 12200, does this increase the weight rating? Even Empty, it rides with 11,000 on the steers. | The Timbren Front Suspension Enhancement System # TKWF001 will not increase the weight rating of your front axle....

My tongue is a 12foot - 2 1/2inch square steel tube with a thickness of 3/16. Is there a Fulton Fold Away unit that will work BEST for my application? | Yes, the Fulton Fold Away Bolt On Hinge Kit item # FHDPB230101 will work for your trailer....

I am 99 certain for my Keystone 273BHSWE below is the right slide topper. Correct? Thx LCV000163300 | The Solera RV Slide-Out Awning part # LCV000163300 fits a trailer with a slide-out 152" to 157" long when measuring the outside flanges. The...

Can you purchase the motor only with out the gear. The magnets in my motor broke everything else is good. | The motor included with the Replacement Gear Motor for Bulldog Electric Powered-Drive Kit # BD1046130-00 that you referenced is not available...

Have 1996 Kenworth with four sealbeam headlamp looking at your conversion kit but the kit dont say if one light is low and one is high been or both low for the wires | On the Vision X Headlight Conversion Kit # VX-46 the black wire is the ground....

I have a 2006 Kenworth T300 pulling a stacker trailer. The brake controller only works by lever. Not by pedal. Clearly the wrong controller. Could you tell me which controller I need to get to synchronize the truck with air brakes with the trailer...

Is there a 2000 watt, 120 volt circulating tank, heater hose mount block/colant heater? Also, is it thermostatically controlled to come on at a specific cold temperature, or just to cut off at the 175 degree maximum. Im looking to mount it...

Will this fit my 2018 XUV 835 John Deere Gator | The Hopkins Plug-In Simple Vehicle Wiring Harness # HM11140585 is designed for the following vehicles: - 2008 - 2009 Mercury Sable - 2008 - 2009 Ford Taurus Sedan Since there aren't any custom...

Could you tell me how to wire a 7pin flat gooseneck trailer with electric brakes to a kenworth t-370 with a 7 pin round | If you need to keep the 7-Way semi active on the truck, then you would need to make an adapter to get it to work with an...

I purchase a superwinch terra45 for my jd825i. What mounting plate is recommended with out modifications? My jd is a 2011. Thank you | The correct custom winch mount for your 2011 John Deere Gator JD825i is the Bulldog Winch Mount # BDW15171....

I have a 2016 590i jd gator xuv. Looking for a winch mounting plate, and/or winch kit. Yeah, new model not much out there | I contacted my tech contact at Bulldog Winch and he told me the Custom-Fit Steel Winch Mount # BDW15175 is confirmed...

My 2011 Kenworth t800 has a 4inch square bolt pattern. The hitch you have pictured is splayed at the bottom 2 bolt holes. If I order this hitch, will you be sending the correct bolt pattern? thanks | The Buyers Products 45 Ton Pintle Hook...

Hook up brite light as per instructions Still no brake lights. Other lights are fine | The brake and turn signal circuits are combined in standard trailer wiring applications therefore, I think there might be an issue with how the tow vehicle...

etrailer ATV Winch - Synthetic Rope - Hawse Fairlead Item # e98988 I would like to install on a 2014 JD Gator 825i. Do you have the mounting plate that will fit the winch to the unit? Is the connection fused? Battery to the winch? | To mount...

Is the connection fused? Battery to the winch? | The Bulldog Winch Powersports Series ATV Winch # BDW15014 you were looking has a sealed 250 amp contactor that acts as a solenoid, and you will use the included wiring to run from the battery...