Recommended Weight Distribution Hitch Compatible with 2010 Ford Explorer w/ Electronic Sway Control
Hi - I have a 2010 Ford Explorer 4.6 v8, with Sway Control option. GVWR: 6280 GCWR: 12000 Curb: 4628 Payload: 1652 I am towing a 2015 Aspen Trail Mini1500BH trailer. GVWR: 3800 Dry: 2975 Cargo: 825 Hitch: 357 Trying to determine the expected...
Can the Rear Hatch of a 2010 Ford Explorer Open with the Reese Cargo Carrier # 63155 is Installed
Can you tell me if this cargo rack is compatible with a 2010 Ford Explorer. If so, does it allow room to open the lift gate while installed? If not, can you recommend something that does fit the above criteria? | By taking a few measurements,...
What Vehicles Does Trailer Hitch # C12130
Trailer hitch used on 1991 Mercury Grand Marquis. What other models will it fit including Ford Crown Victoria? | The Curt Trailer Hitch, # C12130, (installation instructions linked below) will fit the following vehicles: 1983 to 1991 Mercury...
Roof Rack Confirmed to Fit a 2010 Ford Explorer with Raised Factory Side Rails
I currently have aero blades 7501b but I do not think they are correct, they do not even come close to the roof edge. Which racks will work for me please? The configuration page isn’t helping. I can take the factory rails off if necessary. |...
Available Trailer Hitch Classes for 2010 Ford Crown Victoria
I was wondering if I could get the raw materials for this it welded or painted. | All custom-fit hitches made for your 2010 Ford Crown Victoria are shown on the linked page and these include the 2-inch Curt Class III hitch # 13707 that you referenced....
What Wires of 4-Way to 7-Way Adapter Needs to be Connected to Use Curt Echo Mobile
My RV has a 4 post to 7 post adapter the blue black and yellow are not connected to anything will the Curt echo Bluetooth brake controller still work for me ? | You'll need to connect the black wire of your 4-way to 7-way adapter to the positive...
Dimensions of BP08-070 Replacement Manual Brake Adjuster Spring
What are the dimensions of the coiled section.of this spring? Im looking for a replacement for a 1959 Shasta electric drum brake manual adjuster. It has 2 springs per assembly. the current spring 4inch overall, and the coiled section is approx...
Fit of Curt 20x48 Cargo Carrier # C18145 on 2010 Ford Explorer
Will this hitch carrier #c18145 work well on a 2010 Ford Explorer? | To determine if the Curt 20x48 Cargo Carrier will work with your Explorer, you will need determine if there is enough clearance at the rear of the vehicle. You will need to...
Will Draw-Tite Trailer Hitch 41116 Fit 2010 Ford Crown Victoria Police Interceptor w/Dual Exhaust
Does this part fit this model and what is the exhaust mod for dual exhaust? | First, you may not have to do anything with the exhaust because it appears that it may only affect Lincoln Town Car models. In the event that the exhaust on your PI...
Does the Engine Need to Be On So Brakes Work Properly While Flat Towing 2010 Ford Explorer
Since the car has power brakes, does the motor have to be running when towing? | No, the vehicle motor will not need to be running while towing the vehicle in order for the brakes to work. When checking the owners manual for an Explorer, I...
CIPA Towing Mirrors That Fit a 2010 Ford Explorer
Do you sell a CIPA towing mirror that will fit a 2010 Ford Explorer? | We do carry CIPA towing mirrors that will fit a 2010 Ford Explorer. There are three different mount styles available - clamp-on, clip-on, and door mount. The clamp-on style...
Is Drilling Involved when Installing Trailer Hitch # C12130 on a 1983 to 2010 Ford Crown Victoria
Do the Curt hitches require drilling for installation or are the holes already there? | For the 1983 to 2010 Ford Crown Victoria, Sedan and Wagon, you will need to drill 4 holes in the frame in order to install Curt Trailer Hitch, # C12130....
Will the Curt Class lll Trailer Hitch for 2010 Ford Explorer Fit with Factory Hitch and Spare Tire
2010 Ford Explorer Mine is a four door model with the large spare tire and class 2 hitch all ready made on the frame will the Curt part # 13112 fit on corectly with the full size spare tire. and if not what hitch will ? | Yes, the Curt Class...
How to Order Replacement Mounting Hardware for Curt Trailer Hitch 13707
Hello I have a 2010 CVPI and hate to say I have the receiver hitch already. Im in need of the mounting hardware for Hitch #13707, is it possible to get this hardware? I have not an issue paying for it, just let me know. Again thank U for your...
Why Must the Curt Class II Drawbar # C45014 be Used in the Rise Position Only
Why must the ball mount, #C45014, be used only in the rise position and not in the drop position? | I spoke with my contact at Curt and he said the Class II Drawbar, # C45014, has not been tested for use in the drop position. They only test...
Locking Hitch Pin for Factory Trailer Hitch on a 2010 Ford Explorer
My 2010 Ford Explorer has very limited space and the lock must have a side entry for the 5/8inch pin because there is no room to a key into the end of the most common locks. I purchased a side load lock, but there is a bolt head behind the...
How to Order Replacement Hardware for Draw Tite Hitch 75437
hello, looking for a Drawtite bolt kit # 75437F. Do you sell these ? | To order replacement hardware for the Draw Tite hitch part # 75437 what you need is the part # RHK. On the product page of this part number you'll enter the part # 75437...
Replacement Installation Kit for Aries Grille Guard AA3059 for Ford Explorer
Is this kit compatible with Aries Grille Guard model 3059 black or 3059-2 polished? | The Aries Grille Guard # AA3059 does fit your 2010 Ford Explorer and the appropriate Replacement Bracket and Hardware Kit is part # AABRKT-3059. Aries Replacement...
Best Towing Mirror for a 2010 Ford Explorer XLT
What mirror is the best fix for a 2010 Ford explorer xlt | I would be happy to find some towing mirrors that clip onto your factory mirrors but if you are trying to replace your stock mirrors we do not offer any for your 2010 Ford Explorer XLT....
Replacement 7-Way Wiring Harness for a 2010 Expedition EL with Existing 4 Pin Plug
On 2010 Expedition EL, w/ existing 4 pin plug, will this kit be a one/one replacement? or does other wiring have to be done. HD tow pkg is NOT installed. Thanks. | The 2010 Ford Expedition should have a round connector at the rear of the vehicle...
Flat Towing With 2010 Ford E450
I am trying to locate a hitch to use on a 2010 E450 Class C chassis. I need to have minimum 7K pulling for a 4 down situation near zero tongue wt. What is available? Thanks. | I am going to need a bit more information in order to make...
Troubleshooting Wiring on 2010 Ford Explorer
2010 Ford Explorer Eddie Bauer Edition Factory Tow Circuit Problem - The trailer connector on the back of the vehicle has a 7 pin and 4 pin connector. Both connector outputs work except for the Right Turn/Brake output. That tells me its not...
Why Do Hitches have Higher Ratings when Used with Weight Distribution Systems
The specs have different rating when using weight distribution. What does that mean? Is weight distribution automatic with this hitch? | Weight distribution systems are designed to help distribute the tongue weight of the trailer to the front...
Availability of 2-Inch Ball Mount with 6-Inches of Drop and 7500-lb Capacity
I need a ball mount, six inch , at least 700lbs tongue weight, at least 7500lbs towing weight, 2inch ball. Would prefer a ball mount that has the ball pre-torqued onto the ball mount if at all possible. Can you make some recommendations for...
Filter Your Search
Contact and Help