Shockwave 5W Toy Hauler x > Pinnacle x > !Montana Mountaineer Fifth Wheel x > Full Size Pickup x >

When Using the Redarc Tow-Pro Elite In User Controlled Mode Does the Power Ramp Up or Apply Instant

This looks like the perfect controller for my needs: running a trailer with 12V electric brakes from my 24V antique military truck. I also like the small knob on the dash with the main controller mounted remotely. I do have one question: when...

Replacement Gear box for Venture 900-258125

I have a 2015 Shockwave 5th wheel toy hauler. I believe I need a new landing gear box. The landing gear motor is a Venture serial number 9000-258175 LCI PIN 142178 12 vdc - 30 amp. Do you have a replacement gear box that will fit? | The correct...

Recommended Air Brake to Electric Brake Controller for 1969 International Loadstar 1890 Truck

which controller would give better performance I have noticed that instead of using a brake controller like this one, 1300-80, it is recommended to use the , # 90885, brake controller. Is the electric brake controller as consistent with braking...

Can Bulb be Replaced on Peterson Red Flush Mounted Sealed Turn Signal Light 435800

is bulb replacable on this light? what is replacement bulb # | Peterson brake/turn signal light # 435800 is sealed and cannot be opened up to change out the bulb. I pulled one from the warehouse to verify this and cannot get the lens off (without...

What is Correct Placement Of Goose Neck Hitch Ball in Full Size Pickup

where in the bed does the ball have to be front to rear ? over the rear axle,slightly in front the rear axle or can it be 8inch to 10inch behind rear axle??? | A goose neck hitch ball, or the center of a 5th wheel hitch head for that matter,...

5th Wheel Installation Kit for a 1976 Dodge Ram Power Wagon with 6 Foot Bed

is there a install rail kit for my 76 dodge power wagon or will a 2006 dodge ram kit fit my truck | Yes, we have an installation kit for your 1976 Dodge Full Size Pickup with 6 Foot Bed. You will need to use the Reese Universal Base Rails and...

Adjustable Hitch for 1972 Winnebago Brave with Modified Frame

Im looking for a class 5 hitch with 2inch receiver for my Winnebago. There is no ion and the specs are hard to find. The Frame rails C-channel outside to outside at the rear are 34 inches apart, and are 1.75 wide at the rear section. Welded...

How to Determine if Wheel Will Fit on Trailer

Hello, before I order this wheel want to be sure it will fit | I'm happy to help you figure out if the Dexstar Conventional Steel Wheel w/ +0.5" Offset - 16" x 6" Rim - 8 on 6-1/2 - Black # AM20766 will fit on your trailer. In order to determine...

Latch Repair Kits For Titan Coupler and Actuators

Hi, I am wondering if this latch will fit the titan series 80? Thank you! | I contacted Dexter Axle since they acquired Titan and they have not heard of the Titan series 80 actuator or coupler. The Repair Kit for Titan Couplers and Trailer Brake...

How Much Power/Amps Does the Tekonsha Prodigy P3 Draw

Can you tell me what a typical initial surge current Amps or power Watts is for a Tekonsha P3 brake controller when brakes are initially applied? Im mostly running this with a single axle trailer, but will occasionally use it with double axle...

Nerf Bars That Fit 1978 Dodge W150 Truck

Looking for mounting brackets for my Westin 3inch Nerf Bar/Step that Im looking to mount to my 1978 Dodge W150. | There is an option to add nerf bars to your 1978 Dodge W150 truck, though I checked with Westin and they do not have a fit, and...

Will a Sierra Brand 4-Way Flat Trailer Connector Fit Tow Ready Mounting Bracket

I have a Sierra brand tow vehicle 48inch pigtail with connector. Do you know if it will fit this bracket? | Mounting bracket # 18144 fits most 4-Way flat trailer connectors. We don't have Sierra brand connectors so I can't test it. We do know...

Can Peterson Round Flush Mount Trailer Light be Installed in 1/8 Inch Thick Diamond Plate

i am mounting tail lights in 1/8 diamondplate. is this the product i want? i just want to cut the holes and mount with a rubber grommet. i do not want to have to attach light in back or anywhere else. your video explains nothing about mounting also...