!Designer Camper  x   >   !Malibu  x   >   Bulldog  x   >  

Will the bulldog motor 182420 kit mount up right with a bulldog 2 SPEED jacksfor instance 183416 or just the single speed jacks? | The Bulldog Powered-Drive Kit for Single-Speed Jacks part # BD1824200100 as the title states is for single speed...

Need to replace the landing legs which do you recommend. Looking to replace with your item BD500162 will they work? I see the Stromberg is 21 inch rise and these are 18 is that a problem. | In order to pick out a direct replacement for the...

I love this new bulldog coupler that I bought from you last Fall, but my coupler lock that I used with my old Atwood coupler doesn’t fit - the rod is too thick to go through the smaller diameter hole. Can you tell me which of your coupler locks...

I am about to order the BD190758 and want to purchase two additional mounts that I can install near the trailer tires so I can use the jack to lift the tires off the ground when I get a flat. Is the BD005024 the correct female mount that matches...

do you have an exploded view so i can see how the jack screw and nut are connected to the foot | I have attached a photo that has been expanded so you can see what the part # BD500217 jack screw and nut look like. I have also included a photo...

I want to use this in a salt water marine environment. Does this jack have as much corrosion resistance as the 3000 lb. jack Code: BD1550101344 that specifies corrosion resistance? I only need a 2000 lb. jack but I assume I can move up to...

I am thinking of changing the manual jack on my 2002 Kiefer horse trailer. Its a Fulton heavy duty 12,000 lb. jack. Can you please tell me what electric jack kit I need? Also, will I need a gear replacement set? If so, which one? | It sounds...

Will the Bull Dog Powered drive trailer lift no. BD500199 fit a 1985 Airstream With a propane tank cover | We don't have specific information on fits of parts like trailer jacks on individual coaches, but the Bulldog Powered Drive Trailer Jack...

I am looking to replace a missing latch lock but I cant find one anywhere. I have included a picture of what Im looking for. | I may have a solution for you, but unfortunately in this case you can't find one because these low profile latches...

LOOKING FOR A DOWN LEG. FOR A HD2500101 AND HD50001001 FULTON JACK. AND LOOKING FOR THE TOP PLASTIC CAP THAT GOES WITH BOTH MODELS OF THE JACKS. CAN YOU HELP ME FIND THE PARTS, PART NUMBERS AND THE COST OF THE ITEMS. PLEASE LET ME KNOW IF...

My boat weighs 6300#. What jack lift weight do I need to lift the tounge? For an electric jack? my old jack pipe diameter is 2. | To choose the right jack capacity for your boat trailer with a 6,300 lb boat on it, you need a jack with a capacity...

Please confirm the KIng Pin size. We require 2inch exactly | The Bulldog Gooseneck-to-5th-Wheel Trailer Coupler Adapter # BD0289590300 uses the standard 2" diameter king pin. This is generally used on 5th wheels outside of the commercial shipping,...

Length and diameter of bolts that come with #BDA200CO317 | The two bolts used to secure a coupler like the Bulldog Cast Head Coupler part # BDA200C0317 to a channel like the Bulldog 3-Position Adjustable Channel Bracket part # BDAC3000300 are...

What size is the footprint at the base of the jack? Im looking for an ox blox or similar to fit it. | The footplate of the Bulldog Square Jack w/ Round Pipe Mount # BD182524 is approximately 9-3/4" x 10". |

I have a square tube side wind jack on my car hauler. Is there a replacement crank pin that converts the jack to use with a drill? | The only jack that can be converted to be used with a drill would be the Bulldog single speed jacks with a 12K...

I bought a 3500 lb electric a frame Jack from e trailer and it grounds through the trailer. I am going to buy a product called Jack e up which will allow me to disconnect and remove my Jack when hooked up. Do you know how I can get a harness...

Do you have any rack and gear trailer jacks with a 2 inch or 1-3/4 inch outer tubing diameter? | The tube diameter of the Bulldog Rack and Gear Jack part # BD162300 is 1-5/8 inches. That's pretty close to 1-3/4 inches, would that work for you? |

Needing a crank handle for a Coleman tent trailer it an 87 | We don't carry a crank handle specifically for the Coleman Tent Trailers, but we do have many cranks that may work depending on your specific camper. If you are looking for the...

Hello Sir Thanks a lot for your great support. Since the Electric Single Speed Jack # BD1824200100 is used along with the jack on the different weather conditions rain, snow, mud,..., I have a question regarding the environmental protection...

I have a hammerblow hitch on the horse trailer. That has been lets say readjusted. What parts kit do I order to repair it. Thanks | If you want to undo the adjustment to your latch you can use the High-Profile Latch Repair Kit for Bulldog...

Hi, 1 What Sidewind crank is recommended for the 25000 Lbs BD 182701 jack ? Part # please. 2 What model is more reliable with spring return or non spring return ? Thank you | The Replacement Bulldog Sidewind Jack Crank Assembly # BD015181...

Hi i have a trailer with adjustable channel and want to know if this part fits on my channel. The interior of my channel is 3 inches and my bolt spacing from center to center is 2 inches.Thanks. | The Bulldog Lunette Ring for Adjustable Channel...

Hello, I am looking for a wheel attachment for a trailer jack that supports 5,000 lbs. If someone could send me a part number that would be great! Thank you. | There are not any caster wheels that we carry that are rated for that 5,000 lb capacity....

Hi, I am interested in the following articles and I have still questions: - Replacement Mounting Bracket for Trailer Valet Swivel Jack and Trailer Mover Item # TV-0002 - Bulldog 2-4/5inch Long, Weld-On Jack Pipe Mount for 3-1/4inch Male...