!Designer Camper  x   >   !Flagstaff MAC Camper  x   >   1967  x   >  

How do you wirethe vehiclefor a 7 way and elec brakes i tried too do it when you step on the brakes trailer lights go dimm ,turrn on a blinker both trail. Lighfts blink but are dimm i have running lights in trailer with no lights on truck ...

I tow a 11000 - 13000 lb boat with a 2015 gmc 2500 and need more lift to bring the torsion axle trailer to level towing height and Im concerned about hitch fracture safety. I am looking at the 2.5inch Flash Solid Steel Adjustable Ball mount....

Hello. I am looking for a hitch to fit my 1954 F250 truck. I know you dont have any listed for that year. My frame is 34inch wide, and I need it to at least 4inch from the bottom of the frame to the top of the . 6inch would clear the bumper...

Best place to mount the transmission cooler on a 1967 Galaxie 6.4L with AC? | The best place to mount an automatic transmission cooler such as # D12904 on your 1967 Ford Galaxie or any vehicle is in between the vehicle grille and the AC condenser...

On my 1967 Ford F-100? I do not have any connectors, so it will need to be hard wired into truck electrical system. | Do you already have a fully functioning 7-Way connector at the rear of your 1967 Ford F-100? If not then you will need to install...

I need a bikini top for my CJ7. 1986 Jeep. Is there such an animal on the planet? | Yes, there is. I checked with our vendors and the Bestop Strapless Bikini for Jeep item # B5251801 is the correct one for your 1986 Jeep CJ7. |

Do these inside the spring air bags raise the veh. in the rear up to 3 in. if desired ? Thanks inch air lift 1000 drag bags | The Air Lift Vehicle Suspension Kit for the 1967 Pontiac GTO, part # AL60844, is a correct fit for the 1967 GTO (as...

Looking to change out an old Flowmaster exhaust and replace with Dougs headers and your magnaflow stainless steel system. Im just not sure if I should install the larger diameter exhaust or smaller. The article regarding pipe diameter states...

I have a 1967 GMC C2500 8ft. bed, 8 lug W/power disc front brakes conversion, Dana 60 1 ton rear end, GWV 7500lbs trk ID tag. Do you have a frame tie down brace system to fit to hold down a truck camper? or ideas? | There aren't any frame...

Hi! I found your qanda helping a gentleman match a replacement lid for a roof vent on an older camper. Ive got a 40 year-old truck camper with a roof vent that I need to fix. I had been thinking to replace the whole vent, but upon further...

thanks, but i dont need a pump, i just want to put more air in the left side. a seperate shrader valve for each would be ok. | The Air Lift 1000 Drag Bags for Coil Springs item # AL60844 comes with everything you need to set the air bags up...

Do you have dimension specifications for the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 Code: 75122 Can I get the dimensions for this? I am trying to see if it will fit my 1967 Chevy Grumman Olsonette step van. The...

Hello, Can I bolt this flat plate to the top of the frame? What is it rated by itself? Thanks Can this product pull a trailer with just the 6 grade 5 bolts? | Curt says the Gooseneck Flat Plate # C65500 can be installed to the frame rails...

can it be used in a boat where I have a starting battery and a separate battery for my accessories. | Yes, the Deka Battery Isolator part # DW08770 can be used on a boat to separate the starter and auxiliary battery but you would need to mount...

Will this fit a 67 bug? Or any suggestions on a better fit? | If your 1967 Volkswagen Beetle has a 1-1/4 inch trailer hitch receiver at the back then you could use Thule Camber bike carrier # TH9058. If you do not have a trailer hitch you will...

I have a trailer with 2 Dexter 3500 lb axles that have 10inch electric brakes on them. The brakes stopped working. After considerable testing i couldnt find a problem and decided to buy new brake assemblies. I cut the wires that lead to the...

I have a 67 chevelle aluminum radiator bb 427 core dia 22-17 wanting electric fans and shroud to fit what I have also has long water pump I have 2 and five eights from pulley to core need something low profile?? | For your 1967 Chevelle I recommend...

Have a 1967 International Travelall 1200 B which is a 4x4 3/4 ton panel truck. Would like to have a hitch similar to the Curt p/n 15320 that I installed on my Chevy because I have a spare tire mounted underneath the rear similar to the Chevy...

Will this kit work on a 1967 Chevelle SS with a 502 BB? | According to MagnaFlow, the Stainless Steel Crossmember-Back Exhaust System, # MF15897, will fit your 1967 Chevelle SS. This kit is a cross member back exhaust kit. My contact at MagnaFlow...

Hello, What is the width including mounting tabs and what is the distance between the bolts, center to center, frame rail to frame rail? I need a class 5 hitch for a 1967 F350 dump truck. If the width on this doesnt work, do you have a recommendation? Thank...

Can you tell me what the mounting bolt hole diameter is on this fan? | I confirmed with Flex-a-Lite that the bolt hole dimensions on the Flex-a-lite 14" Trimline Reversible Electric Radiator Fan - 12V - 1,585 CFM # FLX114 are 6mm in diameter....

i may try some air bags on my 67 chevelle , do you know if i can get them to inflate individually? | If you use a dual path air compressor like the Air Lift Load Controller Compressor System item # AL25856 you will be able to inflate the Air...

Need to install brake control on 67 ford ranchero really like install kit with module in it can you please send me a total workup from scratch | To install a trailer brake controller like the Prodigy P2 # 90885 in your 1967 Ford Ranchero you...

Hello, could you provide width, length and height of 20000-92230 Do you have a rear truck bumper 78-80inch length? | The Westin # 20000-92230 is 74" long x 8" tall x 8" wide and comes with custom mounting brackets for a 1967 Ford F-100, F-150,...