!CX-9  x   >   Yates Rubber  x   >  

I need a replacement that is 2 7/8 square at the base with a 1/2 inch hole, , 3 1/2 high and the top of the V is 4 3/4 inches...not 6 1/2 as is the 862. Where can I get one like mine? | We don't have a replacement that is an exact fit for your...

I have a 1996 shorelander boat trailer i am looking for 12 rollers and a drivers side fender, i am attaching pictures, the picture is actually the passenger side, but i need the drivers side | The rollers that you need based off of the measurements...

I have been looking on your site for replacement trailer rollers and clips. Existing rollers are similiar to the yates rollers and are 41/2 dia x 31/2 wide .1 inch shaft. Can you supply ? , or compatible replacement. Please respond. Thanks |...

Are these rollers available in non-marking materials | I may have another option for you, but there is nothing like the Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 5/8" Shaft # YR12243-5 you were looking at available...

Hi I have an early 80’s shoreline boat trailer and I’m look for new wobble rollers. They are 5”x3” with a 7/8” diameter bearing opening and a 1” long shaft length. I’m wondering if you sell anything with these dimensions. Thanks | Since you...

My skeg keel is 3” wide. Can you tell me the length of the small diameter portion of the roller? | The inner portion of the Yates Keel Roller for Boat Trailers # YR5244-105EC is 2-3/4" wide. The Roller Shaft with Pal Nuts # CE10722A will be...

My father has a 2016 Shore Lander boat trailer for his 2016 16’ aluminum fishing boat. The issue is the rollers that came on the trailer are sticky and barely roll. This creates a problem for my aging Dad to get the boat on and off the trailer....

I am looking for a roller for my 1982 Calkins boat trailer. I think it is model #21-6400. I am pretty sure about the numbers except the number 1 in the model number. S/N may be 2123 2002. Not 100 sure. Can you help? Thank you , | We carry...

Do these rollers have a bushing inside to make easier spin of them when mounted on a roll pin? | The plastic bushing that is on the inside of the Yates Side Guide Roller for Boat Trailers # YR12243-4P is attached to the rest of the roller and...

have an 06 magic-tilt trailer. Do your wobble rollers work as replacements on my 06? Thanks | There are only a few rollers that we carry that list specific trailers that they will fit. For everything else, you will need to go by the dimensions...

I have a 2015 EZ Loader trailer for my 14foot Smoker Craft fishing boat, the old black rubber keel roller needs to be replaced. I was looking at the 12 inch CE Smith self centering keel roller, with the two piece universal ruler brackets. my...

I need a 2-1/2inch OD roller to fit between existing trailer frame for guiding 2inch strap to eye on boat. I will use a bolt to mount roller between frame. Can you provide this item? What size bolt would I need to mount roller? Please advise...

Need new roller for 1986 Rolco boat trailer. Attached picture shows where center roller is missing. Looking for a roller that is 5inch long, 2 1/2inch diameter. The shaft is .50inch dia. And the sleeve is .73outside dia. Thank you for your...

is a bow roller for just to secure the front of my boat or can it be used to replace the spool rollers that my deep v aluminum boat keeps destroying | A bow roller like the part # YR450Y wouldn't be any more resistant to damage than a spool...

What type of keel roller will use on a hurricane sundeck boat | It all depends on the size of the bracket that you currently have. The Yates Keel Roller for Boat Trailers item # YR18244-165EC you were looking at would work on an 18" bracket....

Im looking on your online catalog for a roller assembly for a pontoon trailer replacement that was damaged and you have the 9-in roller and the 2-in cap and they all say use a one half inch shaft but all I can find in your catalog is the 5/8...

I have a boat trailer that has 3 rollers. 10’m in back 8’m in the middle and it looks to be like 5 1/2 or so in the front. I can’t find the front one on Amazon to order. Is it a bastard size? It’s a Sprint EZ Loader boat trailer. Thanks | The...

Do you have maching blue end caps for the 4inch bow roller? | The white section of the Yates Bow Roller, # YR450B, is molded through the center of the roller. The bow roller does not have caps and is one piece. |

I am looking for a 4inch non marker bow roller that is as close to 4 inch wide as possible like 3.875 wide with as large bell diameters as possible. What is available? | For bow rollers we have 4 inch wide rollers like the part # YR450Y-400Y...

I have a 5X8foot plastic boat, a small Box Trailer and a 2.5 Motor. I would need to attach the saver to the trailer, and I think I would need the the saver with the rubber that goes to the motor. The boat will be securely strapped down to the...

Hi, I am in need of three rollers for the center of my bass boat trailer. the space in between the brackets they get mounted to is 10 in, but they have an inch and a half on either side of the bracket that is also rubber. Im not sure which roller...

my existing solid black wobble rollers are leaving black marks on my hull. will new black rollers do ythe same . my belief is that the older rollers are not as collor fast due ta age and exposure? | The Yates Wobble Roller # YR440R will leave...

Will this bracket support a 4inch rubber v block rather than a roller? Part number YR4Y22-3 | The Yates bow stop # YR4Y22-3 has a base that is 2 inches x 2 inches and a 4-inch span. The base will be to small to work with the panel bracket #...

Which bracket do you use to install 2inch x 2inch base Y- style Bow stop? I can not find 2inch wide bow stop brackets anywhere. Is there other hardwares I can use for this type of stop? Thank you. | You will need a bracket that has a 3/8 inch...