Reese Remov-A-Ball Gooseneck Trailer Hitch Recommendation for a 2004 Chevy Silverado 2500

Question

Question:

Can you use an 04 remove-a-ball hitch 6300 in an 07 chevy? The 04 had an 8 ft bed and my 07 has an 8 ft bed.

asked by: James E

1

Helpful Expert Reply:

Yes, a 2004 Chevy 2500 with a long bed would have had the Reese Remove-a-Ball hitch # 6300-4434 which is the same part number that is confirmed to fit a 2007 model 2500HD with a long bed.

expert reply by: Jameson C

1

Answer 1

The screw and nut assembly, #BD500250, fits Bulldog jacks rated at 10,000 lb lift and 12,000 lb support. We also have kit, #BD500217, which is designed to fit Bulldog series 182 jacks from 2003 to present with a 12,000 lb capacity. I have included a…

view full answer...

Answer 2

To get your Diamond C dump trailer back in working condition you'll need to swap out the entire jack as that internal drive screw isn't available as a replacement. For a replacement jack I recommend going with our etrailer Trailer Jack…

view full answer...

Answer 3

We do sell replacement screw and nut assemblies for Bulldog Jacks. Item #BD500250 fits Bulldog Jacks rated at 10,000-lb lift, 12,000-lb support. It has a rod diameter of 1-1/4 inches. We also offer Item #BD500217, which is designed for use with…

view full answer...

Answer 4

Hey Matt we still have that screw kit. It is the Replacement Jack Screw and Nut Kit for Bulldog Sidewind Trailer Jacks item #BD500217. This is designed to fit Bulldog series 182 jacks from 2003 to present with a 12,000 lb capacity. I have linked a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 8

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 9

Hey Mark. Based on the information you provided, you are talking about the Cummins Onan Generator. The harness you referenced is not going to fit. However, I have one that will. The Replacement 10' Harness for Cummins Onan Generator #CM26RR will…

view full answer...

Answer 10

Hi Wade, Yes, you’ve definitely got some good options to get away from hand cranking, and I totally get wanting something easier, especially with a cattle trailer. A lot of cattle trailers are gooseneck style and use a square center-mounted jack like…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Jesse, cool name! That's definitely a custom project, and there isn't a single off-the-shelf kit that'll give you everything you need. For a lift-up wall that's around 10' x 6', you're looking at building the door and…

view full answer...

Reese Remov-A-Ball Gooseneck Trailer Hitch Recommendation for a 2004 Chevy Silverado 2500

Continue Researching