Replacement Leaf Spring Bushings with Metal Sleeves for 1/2" Bolts
Updated 11/12/2026 | Published 11/09/2026 >
Question:
Hello, I have a question for leaf spring hardware. I have 4 leaf springs that need new bushings. The measurement for the outside is 1 1/8 inch and the mounting bolt is 1/2 bolt. the current ones on there are no good and they have a metal sleeve within the plastic bushing. Do you guys have anything like that?
asked by: Ivan M
Expert Reply:
Hey Ivan!
Thanks for reaching out! We do carry replacement leaf spring bushings, including bronze options that can be a nice upgrade over the plastic bushings you currently have. I do want to double-check a couple of your measurements before recommending anything, though, so we can get you the right fit the first time.
The Dexter Bronze Bushings # K71-291-00 are a popular option for trailer suspensions. Unlike your current plastic bushings with metal sleeves, these are made entirely of bronze, which provides a more durable bearing surface when properly lubricated. They measure 0.69" (approximately 11/16") in outside diameter, 0.57" (approximately 9/16") in inside diameter, and 1.74" long. They're designed for 9/16" suspension bolts, though, so they wouldn't be the correct replacement if your mounting bolts are actually 1/2".
The kit includes four bushings, so you'd need two kits to replace both eye bushings on all four leaf springs, assuming you have standard double-eye springs.
What really catches my attention is your 1-1/8" outside measurement. That's quite a bit larger than the 11/16" outside diameter commonly found on trailer leaf spring bushings. I'm wondering if you measured the outside of the spring eye itself rather than the bushing, or if your trailer uses a less common suspension setup.
Could you confirm whether that 1-1/8" measurement is the outside diameter of the actual bushing or the spring eye? I'd also love to know the length of your existing bushings and whether your mounting bolts are definitely 1/2". With those measurements, I can help narrow down the options without having you order something that won't fit!

Scooter B.
11/11/2026
I’m sure Ivan means the O.D. Of the bushing (teflon or nylon) is 1-1/8” with 1/2” bolt which means the I.D. Of the bushing or sleeve is probably 33/64” or 17/32” with the O.D. Of the sleeve being maybe 11/16”. They are usually a tight fit or slide fit into the nylon bushing hole. Yes that can be a typical set up as I replaced mine a few years ago. They are made to wear on the O.D. Of the nylon bushing inside the leaf spring hole itself. Just make sure your measurements are right by using maybe an inside/outside dial caliper. hope this helps….
Product Page this Question was Asked From
Nylon Bushing - 1/2" Inner Diameter, 7/8" Outer Diameter - 1-3/4" Long
- Trailer Suspension Parts
- Bushings
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- 1/2 Inch ID x 7/8 Inch OD
- 1-3/4 Inch Long
- TruRyde
more information >
Continue Researching
- Q&A: How Wide of a Rim is Recommended for the Tire Size ST225/75R15
- Q&A: Installation of Slipper Spring with Open Eye End
- Q&A: Looking For Square U-Bolt With 1.75" Inner Width
- Article: RV Cell Boosters, How Do They Work?
- Article: What is Overlanding? How to Start your Overlanding Journey
- Q&A: When do Trailer Leaf Springs Need to be Replaced
- Q&A: Replacement Hub for TDE46210
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Standard Color Code for Wiring Simple 4 Wire Trailer Lighting
- Q&A: Bearing Kit for Lippert 4,400 lb Trailer Axle
- Article: Double-Eye Trailer Suspension System Review
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Most Popular Wheel Bearings


Jason T.
11/11/2026
These guys are great to work with as I had to find these bushings for a 1972 trailer and with the correct dimensions provided they will definitely get it right the first time. FYI, I cleaned out the area for the new ones and put a little grease to help with installing.