Looking for 1 inch D-Ring Adapter for Roadmaster Eagle 8000 Tow Bar
Updated 07/13/2026 | Published 07/06/2026 >
Question:
I have a Roadmaster Eagle 8000 tow bar for my motorhome. I am looking for the 1” D Ring adapters for it so I can tow my 2005 Jeep TJ. Do you have them?
asked by: Terry F
Expert Reply:
Hey Terry, for a 1 inch D-ring adapter for Roadmaster tow bars like your Eagle 8000 you would want the part # RM-035-1. Do you have the rest of your flat towing setup figured out?

David A.
7/10/2026
The bushings worked perfectly, a bit of a challenge to redrill my holes. Take your time!!


Paul B.
7/10/2026
Hi Terry, I simply unbolted the plate adapters and bolted in the D-ring adapters and fit snug. No modifications at all.

Paul R.
7/11/2026
The adapter fit my Roadmaster perfectly. Nothing needed to be adapted. Towed my 2003 Wrangler with ease. Good luck!

Russell R.
7/11/2026
It works great I have flat towed my 2009 Jeep Wrangler JK 5 times since I purchased. I am planning another trip the end of the month.
Product Page this Question was Asked From
Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars - 1" Thick
- Tow Bar Base Plate
- Aftermarket Bumper Adapters
- Hitch Pin Attachment
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Blue Ox Base Plate Kit that Fits 2008 Jeep Wrangler Rubicon
- Q&A: How Cand I Use the Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights with My 1" D-Rings?
- Q&A: Trailer Wiring and Flat Tow Wiring for 2025 Bronco Badlands SAS
- Article: Flat Towing Package for 2007-2018 JK Jeep Wrangler and Wrangler Unlimited
- Q&A: How To Use Tow Bar with D-Rings On Jeep Bumper
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Tow Bar to Upgrade and Replace a RoadMaster Falcon 2 Tow Bar
- Q&A: Recommended D-Ring Adapters for Flat Towing a 2024 Ford Bronco Raptor
- Q&A: Recommended Flat Towing Set Up for a 2025 Ford Bronco w/ the Ford Performance Heavy Duty Bumper
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Roadmaster Vehicle Specific Base Plates
- Article: What RV AC Will Work With Your Setup? Avoid Costly Mistakes Before You Order


Richard
7/10/2026
I took two 1/2” pieces of metal and cut them to fit inside the D rings. I then drilled a 7/8” hole in them and welded them together to make 1”. Lots of grinding to get them to fit inside of the d rings. Make sure there is no play, snug fit. The jeep adapters for the road master tow bar, I swapped out and put the jeeo adapters on the tow bar then they fit perfectly through the metal pieces. There is no play going down the road. Make sure the tow bar can travel up and down while connected . I did this for my 2025 Bronco with the factory metal bumper. Not recommended for the plastic bumper or the small d rings, not strong enough. Email if you would like pictures or questions. I would have used 1” thick metal. But only had 1/2”. I used cardboard to mark and cut out a template.