Looking For Replacement Jack For Jayco Tent Trailer
Updated 05/29/2026 | Published 05/23/2026 >
Question:
I am trying to find a replacement jack for my Jayco tent trailer. All the jacks I find have an outside circumfrance of 7 inches which is too big for the hole in my frame. I need one that is 6 1/2 inch. I also need the one with the lower retracted height. I see one with 5 1/8 and that is close and would probably work but it doesnt mention the circumfrance of the needs to fit through the hole in the frame.
asked by: Clark F
Expert Reply:
Hey Clark, thanks for reaching out. You are needing an A-frame jack, right? Most of the ones we carry have a tube OD of 2-1/4". I'm not aware of anything with a 6-1/2" tube diameter.
What is the diameter of the hole in your A-frame?

Mike
5/28/2026
I installed this jack on my trailer. The outer tube is 2 1/4 diameter, the foot plate on the drop leg is 5 1/8, but it will drop completely out to insert the jack thru the mounting hole, then just put it back into the jack leg. It solved my problem of needing more clearance between jack foot and ground.

Product Page this Question was Asked From
Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs - Black
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- A-Frame Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Continue Researching
- Shop: LED Identification Light Bar for Trailers over 80" Wide - Submersible - 3 Diodes - Clear Lens
- Shop: Optronics Streamline LED Combination Trailer Tail Light - Submersible - 11 Diodes - Clear Lens
- Shop: Trailer Hitch
- Search Results: register
- Search Results: sway control
- Search Results: g386
- Search Results: vent garnish
- Search Results: 9106
- Search Results: 133~7~8
- Search Results: dbc~250
- Shop: Mini Momentary Switch - On/Off/On - DPDT - Black
- Shop: Buyers Products Tie-Down Anchor - Cast Aluminum - 5" Long x 2-1/4" Wide - 800 lbs
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Pacbrake Alpha HD Pro Air Bag Suspension Kit w/ Internal Jounce Bumpers - Rear Axle - 5,000 lbs
- Shop: Red Identification Light Bar with White LED Utility Light - 17 Diodes - 15-1/2" x 1"
- Q&A: How to Determine the Fit of a Gen-Y Fifth Wheel to Gooseneck Executive Adapter
- Q&A: Looking For U-Bolts For Haul Rite Pontoon Trailer With 1-1/2" x 2" Axles
- Q&A: Recommendation for an A-Frame Jack with a Lower Retracted Height Than 8 Inches
- Q&A: What Is The Smallest Available Spindle Nut For 2.5k Axle?
- Q&A: 2 inch Outer Diameter A-Frame Trailer Jack Recommendation
- Q&A: How To Stop A-Frame Jack From Scrapping Ground While Going Over Bumps
- Q&A: Shortest Retracted Height Trailer Jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Trailer Hitch Drop
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Can You Flat Tow a MINI Cooper?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)



Les
5/28/2026
I had the same problem on a 1966 vintage travel trailer. The old jack had a 1-7/8" outer tube, I used a, Lichamp Jumbo 2-3/8" Unibit Step Drill Bit for Metal, Extra Large Drill Stepper Bit for Hard Metal Heavy Duty, 12 Sizes from 1/4" to 2-3/8", Spiral Grooved, C5BK from Amazon to bore the hole to fit the new jack diameter. I had 2 levels to go thru, now no problem any jack I want will fit. Installed the etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 5,000 lbs Part Number: e55ZV works great.