Replacement Slide Out Motor for a Power Gear 1010000683
Updated 04/07/2026 | Published 04/05/2026
Products Featured in This Question
Question:
I have a 2000 Mallard 26E with a slide out room that has a motor below the floor and not in a wall. My slide doesn't retract, so I therefore believe I need a new motor and, perhaps new rollers, if I can find out where they are to see if they are worn out, too. Can you help identify the motor, rollers, and anything else that might help solve my problem? Thank you!
asked by: Keith H
Expert Reply:
I sure can Keith! To replace your Power Gear 1010000683 motor, you'll need the Replacement MT Gear Motor Assembly with Pin and Connector B for PowerGear Slide-Outs item # LC67JJ.
Just a heads up, there's no database that shows me what parts are on your 2000 Mallard 26E or what kind of slide out system is on it. Without part numbers and model information off of the system, I don't have anyway of identifying it.
You can add the part numbers, along with any other questions you have, where it says Add Comment. If you would like to email me pictures directly, you can do that as well by sending them to the address you receive this response from.
Product Page this Question was Asked From
Replacement MT Gear Motor Assembly with Pin and Connector B for PowerGear Slide-Outs
- RV Slide Out Parts
- Motor Parts
- Motor
- Lippert Power Gear Slide-Out Systems
- Lippert
more information >
Continue Researching
- Search Results: camplux
- Search Results: motor rv slide out parts
- Search Results: slide out motor
- Search Results: morryde rv steps
- Shop: WFCO Auto Detect RV Converter and AC/DC Distribution Panel - 12V - 55 Amp
- Shop: Lippert SolidStep RV Steps for 29" to 36" Wide Doorways - 3 Steps
- Shop: RV Interior Lighting
- Search Results: accessories and parts
- Search Results: rv windows
- Search Results: rv power cord
- Shop: Furrion RV Refrigerator w Freezer - 10.6 Cu Ft - 12V - Stainless Steel - Right Hand Doors
- Shop: Lippert SolidStep RV Steps for 29" to 36" Wide Doorways - 2 Steps
- Q&A: Can Gustafson 12V RV Vanity Light Use LED Lights
- Q&A: Lumens Out-Put Of The Gustafson RV Vanity Light
- Shop: Replacement MT Gear Motor Assembly with Pin and Connector B for PowerGear Slide-Outs
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Shop: B&B Dual RV Water Inlets - City Water and Gravity Fill - Brass Check Valve - Polar White
- Q&A: Will the 7-Way RV Upgrade Kit ETBC7L Charge the Trailer Battery When Using Curt Echo
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: How to Measure for Trailer Hitch Drop
- Shop: Trailer Wiring
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
- Shop: Suspension Enhancement
- Q&A: Will The 55A WF86FR Converter Power Center Charge My RV Batteries Faster Than The 40A Model?
- Article: Trailer Lighting Requirements
- Shop: Brake Controller
on RV Slide Out Parts
Keith H.
4/7/2026
The slide goes out but hangs up when starting back in. I know the slide motor has a brake on it but the only numbers I have are the US patent number - 5,833,296 - and some other numbers hand-engraved and very difficult to read on the aluminum housing: SE6489, 5-98 (which I assume is the manufacture date of the motor), and what looks like 78-10. I'll send some pictures to you via email shortly. Again, your assistance will be appreciated if it is possible to help me locate and identify rollers that may need replacing and to identify the model number of the slide motor. Thank you so much for your time. All the best, Keith Hughes