How to Determine if Convert a Ball Gooseneck Coupler Is Holding Onto Gooseneck Ball
Updated 03/04/2026 | Published 03/01/2026 >
Question:
We installed this adapter on a 5th wheel we just purchased and noticed on take off and stops, it has a clunk, we couldn’t determine where it was coming from so when we got home, I got into the bed of the truck and my wife drove the truck with take offs and stops. I determined by putting my hands on the adapter that the clunk sound is coming from the coupler around the ball is sloppy. I have a BandW goose neck hitch system with a 2 5/16 ball in my 2016 F350 super duty and we are towing a 2013 forest river wildcat 5th wheel. Not sure what the problem is, I’m not comfortable with the movement allowed between the two. Do you feel that this is safe?
asked by: Matt M
Expert Reply:
Hey Matt, its not uncommon for gooseneck hitches and couplers to make some noise or to see some movement. I don't think it's anything to be too worried about but if you want to test how well it's holding onto the ball have hit connected and latched and then use your trailer jack to try and lift the trailer off the ball and see if it lets it slip out or stays holding onto it. I suspect it will hold onto the ball but it's worth some peace of mind to know for sure.

Matt F.
3/4/2026
Matt, for what it's worth, I owned this hitch as well, and I did notice exactly what you are talking about with mine as well. I came to same conclusion as to the problem, so I did exactly what Jameson C. recommended. I attached it to my truck and lifted and lifted on the landing gear and it only lifted the truck bed with it. I also had a 2 5/16 gooseneck ball. I'm sure it's secure, I pulled gooseneck flatbeds too that all had similar issues, they just tend to have that little bit of slop with the weight transfer. Ultimately, you should have no issues at all if everything is securely mounted and you're under the weight rating, it is just kind of an annoying and disconcerting noice to be sure. I ended up switching to a 5th wheel hitch for my camper for ease of hooking up by myself. (Note: if you do switch style, I would recommend B&W with the dual locking jaws for tight fit and quiet pull. Any fifth wheel with just a slide lock behind the pin will give you the same clunking on stops and starts because there's a gap between the pin and the bar.) Hope this helps you! Happy towing!


Trevor G.
3/4/2026
Some movement, yes. I’m more than satisfied with my purchase. There are no noises to mention. I would seriously consider reviewing your installation process
Product Page this Question was Asked From
Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter - 12" to 16" Tall - 20,000 lbs
- 5th Wheel Gooseneck Adapter
- Adapts Trailer
- 5th Wheel Trailer to Gooseneck Hitch
- No Extra Clearance
- 20000 lbs
- Bolts Over King Pin
- Shock Absorbing
- Convert-A-Ball
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Recommended 5th-Wheel-to-Gooseneck Adapter for 2018 Ram 3500
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Best 5th Wheel to Gooseneck Adapters (2023)
- Q&A: Fifth Wheel to Gooseneck Adapter to Replace Lippert 1621 Pin Box
- Q&A: Demco Recon Fifth Wheel to Gooseneck Adapter that Can be Used with CM Flat Bed
- Q&A: Towing a 5th Wheel Trailer with a Truck That Has a Recessed Gooseneck Hitch
- Q&A: Is the Gen-Y 5th Wheel to Gooseneck Pinbox Bad for the Trailer Frame
- Q&A: Upgrading Pin Box on a 2025 keystone cougar sport 2700bh to the Curt Flex Air 5th Wheel Pin Box
- Q&A: Best Replacement For Iota ILC-3045 Load Center
- Article: Gooseneck to 5th Wheel Adapters
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: How to Raise Your Travel Trailer Height
- Article: Converting Your RV Water Heater to Tankless



Fred B.
3/4/2026
Bolts can loosen on both coupler and gooseneck portion. Use blue locktite. Gooseneck should always be rigid.