What Size Channel Does the BulletProof Hitches 2-Ball Mount for 2-1/2" Hitches MD254 Have?

Question

Question:

MD254 Hitch what is the dimension inside the adjustable track I am looking for a 2” inside width ? Brian

asked by: Brian D

0

Expert Reply:

The BulletProof Hitches 2-Ball Mount for 2-1/2" Hitch item # MD254 has a 3" wide channel with mounting holes 1-1/4" apart and 3/4" in diameter.

For a ball mount with a 2" channel you'll want the Curt Slim Adjustable 2-Ball Channel Mount item # C46KR.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Thanks for the information Gil! The best ball mount options for your 2022 Ford F-350 duallys 3" factory hitch are the B&W Tow & Stow 2-Ball Mount item #BWTS30040B or the Tow & Stow 3-Ball Mount item #BWTS30049B. These ball mounts…

view full answer...

Answer 4

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 5

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 6

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Answer 7

Hey Jason! I'm guessing you have the 12" long shank right now which is the standard. For a longer shank that fits a 2-1/2" receiver you can use the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 16" Long - 7" Rise,…

view full answer...

Answer 8

Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…

view full answer...

Answer 9

Hey Pete! For a hitch I recommend our own etrailer Trailer Hitch #e59ZV. This is a Class III hitch with a 2" receiver and a matte black finish. For custom wiring you can use the Curt T-Connector Vehicle Wiring Harness #C93DQ. This plugs in…

view full answer...

Answer 10

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What Size Channel Does the BulletProof Hitches 2-Ball Mount for 2-1/2" Hitches MD254 Have?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching