What are Wire Gauge Requirements for Progressive Dynamics PD9200 Series Battery Converter

Question

Question:

Hello I woul like more information about this converter for the size of the wire for batteries, I have already a converter charder of the same company Interli Power 40 amps and if I change bigger for charging 3 batteries group 31 What size cable do you recommend for your converter? My inverter is smaller 1000 watts that I am going to change for 2000 Watts Xantrex Prowatt SW 2000 pure sine wave model 806- 1220 Do You sell this inverter ?

asked by: Jean Y

0

Expert Reply:

Hey Jean, so in the install instructions for the Progressive Dynamics converter part # PD9280A the wiring requirements are pretty interesting. For the chassis ground wire they recommend between 6 and 12 AWG.

From battery ground to converter negative they recommend between 2 and 14 AWG, and the same for the battery positive and positive lug of the converter.

So if you have the minimum thickness wire already you do not need to change anything.

expert reply by: Jameson C

0

Answer 1

Hi Lawrence; it sounds like you're wanting to use the Progressive Dynamics 2000 Watt Inverter w/ Transfer Switch #PD64FR with your 50A power system. This is possible and can be seen in the wiring diagram I attached below. The 4,000 watt starting…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What are Wire Gauge Requirements for Progressive Dynamics PD9200 Series Battery Converter

Continue Researching