Weight Capacity of the 79" Inno Square Crossbars

Question

Question:

What is the weight capacity of the INNO Square Base Bars?

asked by: Peter

0

Expert Reply:

Inno has weight tested the 79" Inno Square Crossbars # IN436L and approved them for up to 220 lbs.

This is actually becoming a more common rating for crossbars no matter they style. It's important to note though that usually the legs and/or fit kit for a roof rack system are rated lower than 220 lbs so you'll need to make sure all components of the roof rack system you want to build is rated that high to take advantage of the 220 lb rating.

expert reply by: Jon G

0

Answer 1

The weight capacity of the Yakima CoreBar Crossbars like part #Y00421 is 220 lbs which is for loads evenly distributed across both bars. If you need a higher weight capacity, Yakima does off the HD Crossbars like part #Y01157 which have a 500 lb…

view full answer...

Answer 2

Yes. The Thule Hull-A-Port Kayak Carrier w/Tie-Downs - J-Style - Fixed - Side Loading #TH834 will fit on Rhino Rack Vortex Aero Crossbars like the #RRVA137B, but you'll need 1 of these for each kayak. The Hull-A-Port gives you the ability to…

view full answer...

Answer 3

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 4

Hey William, What is the year of your Ford E-350? There might be a naked roof fit kit that can fit. If not you would need to go with the Rhino-Rack RTC-Style Roof Rack Tracks - 55" Long #RTC14 and rivet it to the roof. If needed you can cut the…

view full answer...

Answer 5

Hey James, yes the Thule TracRac CapRac part #TH29200XT will work for a roof rack that fits the top channels that are on your cap and is compatible with the Thule Hullavator kayak carrier part #TH898 as it can attach to the top channels of the load…

view full answer...

Answer 6

The Thule Hullavator Pro Kayak Carrier #TH898 is only compatible with the Yakima CoreBar crossbars if you also use the mounting kit #TH7520970001. Just be sure that you have the proper clearance (4" - 8" beyond the feet) for this to work…

view full answer...

Answer 7

INNO square crossbars and Thule square crossbars are the same dimensions, 7/8 inch by 1-1/4 inch. The part #INTR would then be compatible with Thule crossbars. To complete the rack for your 2015 Jeep Grand Cherokee you would also need the #INTR132.

view full answer...

Answer 8

The longest load bars we have that will fit the older style of Thule square bar feet is 79 inches with the Inno #IN436L.

view full answer...

Answer 9

The Inno crossbars part #IN436L are the exact same dimensions as the Malone bars so this would work on your Microsport trailer that has shorter bars to extend them out to 79 inches.

view full answer...

Answer 10

The INNO square bars are the same shape as the older Thule square crossbars that didn't have the channel that ran on the underside of the bar. So for a longer crossbar setup you could use the part #IN436L for a 79 inch bar.

view full answer...

Answer 11

If you have the older-generation Thule Podium towers that have the square opening for the crossbars to fit through then yes, you can use the 79" Inno Square Crossbars #IN436L with that roof rack. If you have the newer-generation Thule towers…

view full answer...

Answer 12

While roof rack manufacturers do not specifically make or test their products with products from other manufacturers, I can tell you that the Inno Square Bars, #IN436L, are the same dimensions as the Thule Square Crossbars prior to 2019. Thule…

view full answer...

Weight Capacity of the 79" Inno Square Crossbars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching