Availability Of A 62" Long 9" Wide Teardrop Fender

Question

Question:

do yall have 62x 9 tear fender

asked by: Steve

0

Expert Reply:

We do have some potential options for you, but I am afraid we do not have a teardrop fender that measures exactly 62" long 9" wide.

The closest thing we have will be the # HP94VR fender which is a 65" long 9" wide teardrop fender. I am not sure exactly what kind of trailer you are working with, but if you have room to go a bit longer on the fender this will be the best option. They are also available in stainless # HP34VR.

From there the next closest size is a 60" long 9" wide # HP22FR. These do not have the teardrop either so it likely is not a practical option. More fender/tire clearance is always better than less.

expert reply by: Jesse M

0

Answer 1

Hey Brett, So you do have the Chevy Express chassis (gas) do you have the Mercedes-Benz chassis (diesel)? Could you send me some pictures of your seats?

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hi Andrew, The good news is that for part #HP64VR, there is not a dedicated left or right side because that style fender is universal. Since it does not have built in side specific mounting brackets, either fender can be used on the left side. If you…

view full answer...

Answer 6

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Michael, congrats on the new SUV. The EcoHitch item #EH87CR does not require you to remove the rear bumper assembly when installing. It does require some slight fascia trimming though. You'll have to remove a 2-3/4” deep and 4-1/2” wide…

view full answer...

Answer 9

Hey Morgan, the best hitch for what you are looking for would be the Draw Tite part #DT73RR which has the easiest install and the highest tongue weight rating. The hitch does fit right up under the rear bumper which will slightly reduce ground…

view full answer...

Answer 10

Hey Lawrence, thanks for reaching out. The Curt T-Connector #C56040 is correct for the 2025 Subaru Forester Hybrid. The factory harness plug should be in the rear cargo area behind the driver side access panel. If you remove the trunk floor covering…

view full answer...

Answer 11

Hey Nelson, welcome back and congrats on your new SUV! We get our information directly from Curt and their item #C13409 and item #C47HR hitches fit all models of the 2025 Subaru Forester including the hybrids. This is why we don't list a hybrid…

view full answer...

Availability Of A 62" Long 9" Wide Teardrop Fender

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching