SnapPad Jack Pads For the 7 Leveling Legs On a 2024 Winnebago View 24D Class C Motorhome

Question

Question:

Have 7 inch octagon leveling jacks front and back with EQ SYSTEMS SMART LEVEL on my 2024 Winnebago View 24D. What SnapPads do I need ?

asked by: Joseph C

1

Helpful Expert Reply:

Based on the information I could find you are going to need the SnapPad EQ Compact Jack Pads # SP24FR4. I have included an image you can use to verify your feet do look the same to fit these pads.

expert reply by: Bud M

1

EQ Leveling System 7" Jack Foot With SnapPad Jack Pad
(click to enlarge)

Answer 1

Hey Lisa, thanks for reaching out. What you'll likely need for the 7" octagon foot pads on your 2025 Coachman Entourage are the following: - SnapPad BF 7 Jack Pads for Quadra Bigfoot Leveling Systems w/ 7" Square Jack Feet - Qty 4…

view full answer...

Answer 2

Hey Guy, welcome back! For your Equalizer Leveling System, you'll need the SnapPad EQ Compact Jack Pads item #SP24FR4. These are designed specifically for the feet on your landing gear. They're going to attach directly to them and remain on…

view full answer...

Answer 3

The snap pads you will need for your 2022 Winnebago Navion with 7" octagonal feet is the SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems w/ 7" Square Jack Feet - Qty 4 #SP24FR4. I was able to confirm that with the manufacturer…

view full answer...

Answer 4

Yes, it does! That questions pretty old and it looks like there's been some updates since it was posted. The correct tail light wiring kit for the 2013 Honda CR-V is the Hopkins item #HM56304. This custom fit harness plugs in behind your…

view full answer...

Answer 5

I believe what you have is the 7" square Equalizer jacks on your 2022 Class C RV(see image). This would then use the SnapPad EQ Compact Jack Pads for Equalizer Leveling Systems #SP24FR4. If this does not match your jack, please send me any…

view full answer...

Answer 6

There are rare occurrences of the SnapPads falling out, but that is very uncommon and tends to be due to improper pad being used. Since you know that your 2020 Dynamax Isata 3 has 7" square jack pads then the SnapPad EQ Compact Jack Pads for…

view full answer...

Answer 7

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 8

Hey David thanks for the information! I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET. This system has a tongue weight range of 800 lbs - 1,200 lbs so you'll be covered if you load your trailer up…

view full answer...

Answer 9

Hey Richard, thanks for reaching out and providing a photo! I spoke with my contact at TireMinder and they said that there unfortunately aren't any replacement parts for the TireMinder Tire Pressure Gauge #TMG-AAA-Multi. If it was within the…

view full answer...

Answer 10

Hello Jay, thanks for reaching out. The Curt Pop-In Ball #C60601 is 6-13/16" tall overall. I have included a picture with some dimensions for your reference. Why are you needing the ball to be a specific height? Just curious.

view full answer...

Answer 11

The Kuat NV 2.0 bike rack you referred to, part #NV22G would work great in the hitch on your truck when you use an adapter like part #HT02. The rack is NOT recommended for use on the rear of a towed travel trailer. Bike racks installed on the rear of…

view full answer...

SnapPad Jack Pads For the 7 Leveling Legs On a 2024 Winnebago View 24D Class C Motorhome

Product Page this Question was Asked From

Continue Researching