What Does Curt Adjustable Ball Mount # C99NR Weigh

Question

Question:

How much does this hitch weigh?

asked by: Austin S

0

Expert Reply:

The Curt adjustable ball mount part # C99NR that you referenced weighs 36 lbs.

expert reply by: Jameson C

0

Answer 1

Great question Luke! These are all great options, but let me point out a few differences for you. The etrailer Adjustable 2-Ball Mount #e66PR is a good quality, affordable option compared to similar options like the BulletProof Hitches 2-Ball Mount…

view full answer...

Answer 2

The Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2" Hitches #ERT00108 requires at least 1" of the shank to properly fit. I went out and measured the shank on the Curt Adjustable 2-Ball Mount #C99NR and found the from the center of…

view full answer...

Answer 3

Hey Jonathan, you are correct. The etrailer Adjustable Ball Mount #E66PR has been tested on a 2024 Nissan Frontier and because the hitch receiver sits too far inside (only 3" from hitch pin hole to bumper), this ball mount will hit the bumper…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Pete! For a hitch I recommend our own etrailer Trailer Hitch #e59ZV. This is a Class III hitch with a 2" receiver and a matte black finish. For custom wiring you can use the Curt T-Connector Vehicle Wiring Harness #C93DQ. This plugs in…

view full answer...

Answer 9

Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…

view full answer...

Answer 10

Hey David! The TowSmart Adjustable 2-Ball Mount #TS89VR cannot be flipped around and stored under your truck. The back of the shank/mount sticks out so you wouldn't be able to mount the ball platform on the other side. See the attached picture.…

view full answer...

Answer 11

Hey David. I would go with a different ball mount if you're concerned about being able to adjust in 1-1/2" increments. I recommend the etrailer Adjustable 2-Ball Mount item #e66PR. Comparably it's pretty similar to the Bulletproof item…

view full answer...

Answer 12

The B&W Tow and Stow ball mount #BWTS10049B will have some great features. You can stow the mounting platform that has the 3 hitch balls (1-7/8, 2, and 2-5/16 inch) underneath your vehicle. This is nice because you will eliminate the possibility…

view full answer...

What Does Curt Adjustable Ball Mount # C99NR Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching