Replacement Heating Pad For Thomas Payne Recliner With Power Recline

Question

Question:

I have a Thomas Payne dual recliner theater seat arrangement. Both chairs have electric recline. My heating pad wire connector has a 12 volt label on it. What is the correct heating pad replacement?? Thanks

asked by: John D

0

Expert Reply:

Thanks for that info; since you have the power recline on your Thomas Payne recliner, the correct replacement heating pad is the following:

- Replacement 29-Volt Seat Heating Pad for Thomas Payne Seismic Series RV Couches and Chairs # 674864

expert reply by: Kyle S

0

Answer 1

Hi Eugene, welcome back! We're pretty limited on sizes and colors since it depends on what Lippert has available at the time for this line. We have the following two options in a 67" length: -Thomas Payne Trifold RV Loveseat and Sleeper -…

view full answer...

Answer 2

I apologize for your issues with your heating pads! The Replacement 12 Volt Seat Heating Pad for Thomas Payne RV Theatre Seating #LC38UD is the same pad as the 354491. The 354491 is the Lippert part number and the #LC38UD is the part number here at…

view full answer...

Answer 3

I spoke with my contact at Lippert who said that either the heater is bad or the control box needs to be replaced on your Thomas Payne Momentum recliner. To test the heater unplug the red and black wires from the control box (located behind and under…

view full answer...

Answer 4

It sounds like you have the heating pad in your chairs and are missing the wiring harness that connects the seat heater to everything else. The Replacement Seat Heater Kit for Thomas Payne RV Furniture #195-000113 connects to the two prong connection…

view full answer...

Answer 5

There could be 2 different issues here, so I'll give you a way to test out the control box which will help us figure out what the issue might be. To test the heater unplug the red and black wires from the control box (located behind and under…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Heating Pad For Thomas Payne Recliner With Power Recline

Product Page this Question was Asked From

Continue Researching