Replacement City Water Inlet/Check Valve For 2020 Grand Design Momentum 353G 5TH Wheel RV

Question

Question:

Good day. I’m looking for a replacement brass City fresh water connection/ check valve for my 2020 Grand Design 353G.

asked by: Joshua S

0

Expert Reply:

You will need to check your current city water inlet to determine if you have a Female # A01-0175LFVP or Male # A01-0169LFVP thread for connecting to your water lines on your 2020 Grand Design Momentum 353G 5th wheel.

expert reply by: Bud M

0

Answer 1

The MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways will be correct for a 2020 Grand Design Momentum 29G. That said, you'll need to measure the entry height to get the correct model; part #MR26RR for 25-29", part…

view full answer...

Answer 2

The doorway width - the width from flange to flange of your doorway - needs to be between 23-3/4 inches and 26-1/4 inches, so yes, your 24 inch door will allow you to use the MORryde steps you asked about, which are the following part number: -…

view full answer...

Answer 3

Thanks for the picture Mike! The MORryde StepAbove RV Steps #MR48RR you were looking at will still work just fine with your threshold that's around 1/2" tall. The issue comes more into play with the threshold being too tall not allowing the…

view full answer...

Answer 4

You are right on. The 8" rise/drop on the MORryde StepAbove Fold-Down Steps #MR98RR is the height between the steps. The #MR48RR you were looking at has a 9" rise/drop meaning the distance between the steps is 9". The #MR98RR is…

view full answer...

Answer 5

The MORryde STP-206 is our MORryde StepAbove RV Steps item #MR98RR.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement City Water Inlet/Check Valve For 2020 Grand Design Momentum 353G 5TH Wheel RV

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching