Height Of SeaSucker Monkey Bars Roof Rack # 298-SX6000B To Bottom of Crossbar

Question

Question:

How high off the roof surface is the bottom of the monkey bars? I have an unusual application—I need to carry SUPs on a boat for ship-to-shore access. The cabin roof on the boat has a hump in the middle of it, about 4” high. Will the monkey bars be able to straddle it?

asked by: Bill H

1

Helpful Expert Reply:

The SeaSucker Monkey Bars Roof Rack # 298-SX6000B will position the bottom of the crossbar 4-1/2" above the roof at the mounts. As long as your roof curve and hump does not exceed this you will be able to use them to carry your Stand Up Paddleboard.

I recommend using a set of Pads # 298-SA1022 and Cam Buckle Tie-Down Straps # 298-SA0010 to secure your SUP and protect it from damaged on the round bars.

expert reply by: Bud M

1

Answer 1

I went ahead and did research on your 2022 Toyota 4Runner, and the owner's manual recommends installing tire chains on the rear tires only. Also, the manual recommends that the link thickness should not exceed 5mm. When considering tire chains,…

view full answer...

Answer 2

For your 2011 Toyota Sienna without siderails, the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount - 48" Long #298-SX6000B is a great option. It uses vacuum mounts that each have a 210 lbs pull strength rating. Then you can use the SUP and…

view full answer...

Answer 3

We have the perfect option for you and your Tesla Model X and it is a very straight forward easy solution too. Since you do not already have a hitch installed on your 2017 Tesla Model X, I suggest the SeaSucker Ski and Snowboard Carrier, #298-SK2425.…

view full answer...

Answer 4

I reached out to a representative of Yakima who told me that for the 1-1/4 inch diameter round crossbars of a SeaSucker roof rack like the #298-SX6000B, the Universal MightyMounts for Yakima Roof Mounted Accessories #Y03590 will fit around them. They…

view full answer...

Answer 5

Since the Malone Microsport trailer part #MPG460G has a tongue width of 2 inches you could use the tower kit part #CE31013G which is 30 inches tall as this is designed to fit 2 inch channels. Then you could use a winch like the Buyers Products part…

view full answer...

Answer 6

You have nothing to worry about! According to SeaSucker, all of their products like the SeaSucker Monkey Bars Roof Rack #298-SX6000B that you have for your 2008 GMC Canyon are compatible with fiberglass surfaces. Along with fiberglass surfaces, their…

view full answer...

Answer 7

Hello Dustin. I looked at the answer that you are referring to. The manufacturers have not been able to test fit at this time, so they do not have it listed. However, here at etrailer.com we have an entire team dedicated to our fit guide which is why…

view full answer...

Answer 8

Hi Yanick, None of the manufacturers we offer currently have a confirmed fit for the 2025 Chevy Equinox EV yet, which means they just haven't had one in their shops yet to confirm. The Curt #C89RV probably will end up fitting but there does seem…

view full answer...

Answer 9

Thanks for the photos, and although we do have a solution for you, the Curt Vertical Receiver Adapter #C45013 will only work with vertical OEM hitch receivers, which your 1992 Ford E-350 does not have. Additionally, any type of adapter is going to…

view full answer...

Height Of SeaSucker Monkey Bars Roof Rack # 298-SX6000B To Bottom of Crossbar

Product Page this Question was Asked From

Continue Researching