Can Spacers Be Used With The Ultra-Fab Power Twin II Manual Stabilizer # UF39-941704

Question

Question:

Can you use a down spacer with the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30 Lift - 6,000 lbs Item # UF39-941704? To get below a gas line that is attached to the edge of the frame.

asked by: Perry

0

Expert Reply:

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 needs to attach directly to the frame of your trailer so I recommend either sliding the stabilizer over a bit on the frame to clear the gas line or to reroute the gas line around where the stabilizer will mount.

expert reply by: Kevin C

0

Answer 1

The best option from Lippert is the Lippert High-Speed Power Stabilizer Jack, #LC298707. But in this style of stabilizers, I prefer the Ultra-Fab products, they have the Power Twin II Electric Stabilizers with Dual Motors, use #UF39-941705 for a…

view full answer...

Answer 2

I spoke with our contact at Ultra Fab and the bolts are upside down in our product pictures of the #UF39-941704 that you referenced. When they are installed properly they would not interfere with the mounting surface.

view full answer...

Answer 3

If you're talking about a space to sit between the mounting brackets of the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 and the frame of the trailer then no, this stabilizer does not have spacers. If you're trying to gain more…

view full answer...

Answer 4

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs #UF39-941704 measures 5" from the trailer frame to the lowest hanging part of the jack. I confirmed this with my contact at Ultra-Fab. Since your trailer has a lower profile it…

view full answer...

Answer 5

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs #UF39-941704 that you referenced is designed to be bolted on with the included mounting hardware. The difference between the #UF39-941704 and the #UF39-941705 is that the #UF39-941705…

view full answer...

Answer 6

There isn't a manual version of the Ultra_Fab Power Twin stabilizer jack with 22 inches of lift but I do have some options for you. You can use Valterra Folding Manual Stabilizer for Trailers and RVs - 14" to 28" Tall - Aluminum Item…

view full answer...

Answer 7

The mounting bracket for the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 is approximately 35-3/8" in length. The frame height would dictate the amount of lift you would want but there are other factors to take into account. The…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Katja, the Curt Echo Mobile brake controller part #C51180 would be your best option. This is a wireless brake controller and all it requires is a 7-way with the taillight functions and the 12 volt accessory circuit active and you'd be set. So…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 12

Hello, and thanks for getting in touch. The etrailer Electric Trailer Jacks #e55ZV and #e23ZV will hold up just fine in cold weather. The housing is designed to be water/weather resistant. It even has a manual backup option if you were to lose power…

view full answer...