Will Dutton-Lainson Remote Hand-Held Switch Work With Older StrongArm Winch

Question

Question:

I have a STRONG ARM 120 V 8 AMP. FOR MY boat lift Model LR 90865 . Its an older model but working fine. Will this switch work on that model?? Regards

asked by: Dave S

0

Expert Reply:

Yes, you will be able to use the Dutton-Lainson Remote Hand-Held Switch # DL24052 with your existing Dutton-Lainson StrongArm LR90865 winch. This will wire directly to your winch and will allow you to control the load and unload functions.

expert reply by: Robin H

0

Dutton-Lainson StrongArm LR90865.
(click to enlarge)

Dexter #9 Torsion Axle On 2005 Shadow Cruiser T139
(click to enlarge)

Answer 1

I wouldn't submerge the Dutton-Lainson Remote Hand-Held Switch for AC StrongArm Electric Winches #DL24052 but it would handle some exposure to weather and water. When not in use I would recommend storing it out of the direct path of rain though.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Will Dutton-Lainson Remote Hand-Held Switch Work With Older StrongArm Winch

Product Page this Question was Asked From

Continue Researching