Single Step Replacement for ETD 728 Elkhart Tool and Die Step

Question

Question:

What can step ETD 728 Elkhart Tool and Die be replaced with? Thanks,

asked by: Jennifer P

0

Expert Reply:

For a single pull out step you could use to replace your ETD 728 Elkhart Tool and Die step you'd want the part # SMFP-1100.

expert reply by: Jameson C

0

Answer 1

Hey Tom, With those Magnetek 6700 Series no longer being around I recommend the Progressive Dynamics #PD4045KA. This is an upgrade since we no longer carry any 30-35amp units, this will upgrade you to 45 amps of output. You will need to modify the…

view full answer...

Answer 2

Hey Cory, so If I'm understanding correctly you just want to use your Curt 5th wheel with your Reese rails? If that's the case, then yes you can, you just have to make sure that your Curt slider uses the standard industry standard connection…

view full answer...

Answer 3

The Trailer King RST are a pretty middle of the road tire, not bad but not a top of the line tire. On the other hand the Kenda Loadstar ST tires are a high quality tire designed and strenuously tested in Ohio to make sure the tires are as reliable,…

view full answer...

Answer 4

Hey Mike, great question! I reached out to Dometic and they said the Dometic Soft Start for FreshJet Mechanical Air Conditioners #DMC87RR is also compatible with the FreshJet 5. You can use this to add a soft start to your new AC unit. Any big trips…

view full answer...

Answer 5

It is possible to upgrade your Fastway e2 Round bar weight distribution system by using higher rated spring bars. I assume you have the 600 lb system, part #FA92-00-0600, so you can upgrade to a 800 lb tongue weight or 1,000 lb tongue weight system.…

view full answer...

Answer 6

Thanks so much for the kind words that's really nice to hear, and we do have a possible option for a keyless entry door, but don't know the exact fit so it will require some measuring. What you need to do is measure the entry door lock cut…

view full answer...

Answer 7

Put the pin back in and wind it 12-16 times rolling it towards the camper to put the correct tension in the slide topper #LCV000163285 before installing it. This will give you the correct amount of tension for extending and retracting the awning.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Single Step Replacement for ETD 728 Elkhart Tool and Die Step

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching