Is There a Fold-Away Trailer Tongue Coupler Kit for a 3x4 Trailer Frame

Question

Question:

looking for a 3x4 bolt on trailer tongue fold away kit

asked by: Todd

0

Expert Reply:

I do have a fold-away trailer tongue coupler kit that will work on a 3x4 trailer frame, the Fulton Fold-Away Coupler Hinge Kit part # FHDPB350101. That said, you will need to use shims/spacers to fill the rest of the gap. This is actually explained in the instructions and very common so no need to worry.

expert reply by: Conner L

0

Todd

6/10/2020

Thanks for checking into this , my customer is going to pass as they do not want to install spacer's to fill the 1 inch gap Thanks

Answer 1

I spoke with my contact at Fulton and as long as the part that swings away when using the Fulton Fold-Away Coupler Hinge Kit #FHDPB350101 is not very long (which is doesn't appear to be) you will be just fine. If it were fairly long then you…

view full answer...

Answer 2

The Fulton Fold-Away Coupler Hinge Kit, part #FHDPB350101, is intended for use on steel (but not aluminum) boat trailers that have a tongue size of 3 x 5 inches. Yes, this is the internal dimension of the two coupler halves. When installed the two…

view full answer...

Answer 3

The overall length of the Buyers Products Straight Tongue Trailer Coupler #3370091562 that you referenced is 17-1/4 inches.

view full answer...

Answer 4

The Zinc Plated Fulton Fold-Away Coupler Hinge Kit for 3" x 5" Tongue - Bolt On - Up to 9,000 lbs #FHDPB350101 is the only option we have for your 3 x 4 inch tongue. You would need to install 1/2 inch spacers on the top and bottom of each…

view full answer...

Answer 5

Buyers Products Straight Tongue Trailer Coupler #3370091562 should be installed with bolts through all three holes in the channel mount so that it can meet its published weight specs. Two of the holes are spaced at 3-inches on center; the third is…

view full answer...

Answer 6

For your 2019 Silver Creek Silverback 35IK, you can use either two of the single axle kits #LC87120 for your tandem axle trailer, or you can use 1 of the tandem axle kits #RR23QX. The tandem axle kit is the exact same as two of the single axle kits,…

view full answer...

Answer 7

From the weight capacities you listed, I suggest going with the SumoSprings #SSR-610-40. This will give you the needed support while not affecting the ride as much as a higher capacity option. I do have to mention, however, that all the suspension…

view full answer...

Answer 8

First, thank you for your service! Unfortunately we don't offer a discount simply because we try to give all of our customers the lowest possible price at any given time. For your 2020 Chevy Traverse I recommend the RedArc Tow Pro Elite #RED44FR…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Is There a Fold-Away Trailer Tongue Coupler Kit for a 3x4 Trailer Frame

Continue Researching