Hidden Trailer Hitch Made In USA for 2019 Subaru Ascent

Question

Question:

Is it made in the USA?

asked by: Kenneth

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver # 76253 that you referenced is made overseas.

For a similar trailer hitch with the same hidden design we do have the Eco-Hitch # 306-X7381, which is confirmed to fit your 2019 Subaru Ascent and is made right here in the USA. The 2 inch receiver on this model will sit behind the factory knockout panel on the bumper (see attached image) and it features a 5,000 pound towing weight capacity.

expert reply by: Chris R

0

click to enlarge

Answer 1

For your 2021 Subaru Ascent there are four trailer hitch receivers that will be all be hidden behind the center bumper cover, the EcoHitch #306-X7381, the Curt #C25VR, the Draw-Tite #76253, and the etrailer #e55ZR. These hitches are all pretty…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 9

Hey Ben! The Curt does have that restriction on the vertical bike racks so I recommend the TowSmart Trailer Hitch #TS82VR. This has a higher tongue weight capacity and will allow you to carry the VelociRAX. It would be a good idea to add the etrailer…

view full answer...

Answer 10

Hey Gregory, thanks for reaching out. Yes the Curt #C13195 hitch is exactly what you'll need for carrying a few bikes on the back of your 2020 Hyundai Santa Fe. it has a 2" receiver and 750 lb tongue weight capacity so 4 bikes will not be a…

view full answer...

Answer 11

The Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR can definitely be installed on your 2021 Subaru Ascent, but how it hooks up to your vehicle will depend on how it came wired from the manufacturer. If you have the factory tow package, the…

view full answer...

Answer 12

Hello John, thanks for reaching out. According to the online spec sheet, the 2025 Keystone Coleman 13B does use the ST215/75R14D tires. So the Loadstar ST215/75D14 Bias Trailer Tire with 14" White Wheel #AM3S550 you mentioned will work great as…

view full answer...

Hidden Trailer Hitch Made In USA for 2019 Subaru Ascent

Products Featured in This Question

Continue Researching