Usable Length of Trailer Suspension Wet Bolt # 126A1

Question

Question:

THE 126A1 is listed as 3 1/2inch long. Is that the 3/4inch length or does it include the hex head of the bolt as well. If so, I need a 3/4inch x 4inch including head with a zerk. Do you carry such a bolt?

asked by: Gary

1

Helpful Expert Reply:

The length figure for the wet bolt part # 126A1 is measured from the below the head to end of the threaded section. So that does not include the hex head. I'd recommend measuring the usable length you need from your bolt. Most likely this will work for you though as this is a very common size for trailer suspension.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I called the supplier (Redline) and they said the only wet bolt they offer in a 9/16 inch diameter is the Redline Wet Equalizer Bolt, #126B2. The length of this bolt, not including the head of the bolt or the threads is 2-5/16 inches. The only other…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 11

Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?

view full answer...

Answer 12

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Usable Length of Trailer Suspension Wet Bolt # 126A1

Product Page this Question was Asked From

Continue Researching