Replacement Handle for Fulton Magnum Series Jack

Question

Question:

The only thing I can find on the tongue jack is on the cover and it just says Fulton Magnum Series (I think I said Maximum series previously) If a handle isn't available, can you tell from the photos that I sent if you have a jack that will interchange with the one that I currently have?

asked by: Raymond

1

Helpful Expert Reply:

It may be possible to get another handle; I would need to know the model number of your jack in order to see if there is a compatible replacement. Do you know the model number of your jack? I was unable to find any reference to a Fulton Maximum Series.

expert reply by: Kyle S

1

click to enlarge

Raymond

1/10/2019

The only thing I can find on the tongue jack is on the cover and it just says Fulton Magnum Series (I think I said Maximum series previously) If a handle isn't available, can you tell from the photos that I sent if you have a jack that will interchange with the one that I currently have?

Kyle S.

1/10/2019

We do have handles for Fulton Magnum Series jacks! What you will want is Replacement Sidewind Handle Kit # F0933301S00 if your jack has a capacity of up to 800 lbs. It is designed for the following Fulton jack models: TJ503/C, TJU503, PMJ53, TJ100, TJ507/C, PMJ75, CS750, GR700/TJ712, XP10/L/W/WC and XP100. If your Fulton Magnum Series jack is rated for up to 1,500 lbs you need the Replacement Sidewind Handle Kit # F0933305S00. It is designed for the following Fulton jack models: TJ1055, TJ1057, TJ1222, TJ255, TJD125, TJ122F, XP15/L/W/WC and XP15L.

Answer 1

I spoke to my contact at Fulton and he informed me that the Fulton Magnum series jacks were an older line of jacks that had capacities of over 1,000 lbs. Without knowing what capacity your jack is or what model it is it would be hard to pick out the…

view full answer...

Answer 2

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 3

The Replacement Sidewind Handle #TJD-7000S-HD is 2-9/16" from the center of the 3/16" roll pin hole to the end of the 1/2" shaft. It has a length of 3-13/16" from the end of the shaft to the inner side of the shaft(see image).

view full answer...

Answer 4

I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part #TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check…

view full answer...

Answer 5

Thank you for that photo, and while we do have the parts you need, the plastic part of the handle and retaining clip are not available as individual replacement parts so you will need to get the replacement handle, which comes with those parts. The…

view full answer...

Answer 6

We do have the replacement handle kit for your Fulton Round Snap-Ring Swivel Marine Jack #FTJ12000101 with part #F0933305S00. Just the hand grip portion of the handle though is not available as a separate part from the manufacturer. The Handle Kit…

view full answer...

Answer 7

Both the Fulton 800 lb Handle #F0933301S00 and the 1,500 lb Handle #F0933305S00 have the same diameter so you just need to make sure that the distance from the end of the handle to the pin hole is similar to what you currently have.

view full answer...

Answer 8

With the Magnum series of Fulton jacks being obsolete you will want to disassemble your jack to verify if the handle shaft matches on the Replacement Sidewind Handle Kit #F0933305S00. Even with knowing the model number on your Jack it is difficult to…

view full answer...

Answer 9

You have two choices for a replacement handle for the obsolete Reese trailer jack 74410. The first option is the Fulton Sidewind 800 lb Handle #F0933301S00. Your second option is the Fulton Sidwind 1500 lb Handle #F0933305S00. My technical contact at…

view full answer...

Answer 10

We do offer a couple of replacement handles that are designed for Fulton jacks. part #F0933305S00 is designed to fit Fulton jack models TJ1055, TJ1057, TJ1222, TJ255, TJD125, TJ122F, XP15/L/W/WC and XP15L. I have attached a photo of this handle that…

view full answer...

Answer 11

Hello Paul, thanks for reaching out. The Fulton Magnum jacks are an older line of jacks that are no longer made. Fortunately Fulton hasn't changed their design much so they still make compatible handles. If the Fulton Magnum series has a capacity…

view full answer...

Answer 12

It looks like you have a Bolt-Thru style Fulton Swivel Marine Jack therefore the correct replacement for you would be part #FXP10 which has a 1,200 lb weight capacity. This jack would then use the same mounting bracket you have now but it does come…

view full answer...

Replacement Handle for Fulton Magnum Series Jack

Featured Help Information

Miscellaneous Media

Continue Researching