Recommended Electric A-Frame Jack for 2010 Keystone Laredo

Question

Question:

Looking to replace the original jack on my 2010 keystone laredo 291tg - After reading many reviews and q and a’s, I think I’m narrowed down. What do you think about the bulldog? I like that it has a 5 year warranty. I’m just trying to get a quality jack at a decent price. Thank you.

asked by: Mark L

0

Expert Reply:

IThe Bulldog Powered Drive Trailer Jack # BD500199 is rated for 4,000 lbs with 22" of lift. It does have a great 5-year warranty, compared to the 1-year or 2-year warranties of other electric jacks in its class.

The Bulldogn # BD500199 has been well reviewed and Bulldog has an outstanding reputation for the quality of their jacks. Due to that and the long warranty if it were me I'd go with the Bulldog # BD500199.

expert reply by: Kyle S

0

Answer 1

I was able to go out to the warehouse and measure the width of the head on the Bulldog Powered Drive Trailer Jack #BD500199. The head is approximately 4-1/2" wide at its widest point.

view full answer...

Answer 2

The Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black #BD500199 uses an ACME screw, not a ball screw. An ACME screw uses a trapezoidal shape thread to roll onto the lead screw and does not use ball bearings.

view full answer...

Answer 3

From the center of the jack tube to the outside edge of the head cover on the Bulldog Powered Drive Trailer Jack #BD500199 is 4",and the head cover extends out 1" from the edges of the jack tube. I've attached some diagrams for you to…

view full answer...

Answer 4

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 5

Thankfully basically all trailers use the same dimensions for the mounting brackets of their jacks which means any power jack like the Bulldog part #BD500199 that you referenced would fit and work great. My favorite is the Phoenix electric trailer…

view full answer...

Answer 6

Hey Marc. Adding a battery to the trailer is definitely the best way to power an electric tongue jack like the #EJ-3520-BBX. That said it is possible to wire it to the 7-way, and there are two ways to do this. Option 1: Add a junction box like part…

view full answer...

Answer 7

The replacement level for your Bulldog Powered Drive Trailer Jack #BD500199 is found as part #BD500193 on our site. It does come with the screws as well.

view full answer...

Answer 8

Since you are using the trailer jack for your show car trailer I highly recommend the Bulldog Powered Drive Trailer Jack #BD500199 because it features a spring-loaded pull pin to quickly adjust the lower leg, 4"-6" of overlap between inner…

view full answer...

Answer 9

You are correct in that the Fastec Electric Trailer Jack part FIC 3500 that you have now is rated for 3,500 lbs. It also offers up to an 18" lift. You can certainly use a 4,000 lb jack in place of this and for that, I recommend using the Bulldog…

view full answer...

Answer 10

The only difference between the two Bulldog Powered A-Frame Jacks part #BD500199 and #BD500200 is the color. One has a white housing and the other has a black one.

view full answer...

Answer 11

What you described is actually the best solution! Connecting your battery to 12V Power wire from the 7-Way on your trailer is a great way to provide a maintenance charge on your battery to operate a Bulldog jack like part #BD500199. Mounting a…

view full answer...

Answer 12

The Snap Pad Jack Pad for Camper Jacks w/5-1/2" Round Feet Item #SN97FR is going to be too big to snap on to your 5.278" foot. What you can do instead is use the Stromberg Carlson RV Jack Pads for RVs and Trailers - 9" Long x 6"…

view full answer...

Recommended Electric A-Frame Jack for 2010 Keystone Laredo

Featured Help Information

Miscellaneous Media

Continue Researching