Release Latch Recommendation for Roadmaster Blackhawk 2 Tow Bar

Question

Question:

Can I purchase just the release latch for the Blackhawk 2 All Terrain or do I have to purchase the whole yoke? The release latch for 910019-20C Thanks

asked by: Scot

0

Expert Reply:

For just the release latch of your BlackHawk 2 Tow Bar part # RM-422 the correct part number is the # RMB001353.

expert reply by: Jameson C

0

Answer 1

Yes, the repair kit part #RM-910003-60 does work on a Roadmaster Blackhawk 2 tow bar.

view full answer...

Answer 2

I'm assuming you're speaking of the 3/4 inch bolt and nut that joins the yoke to the stinger assembly, which are items #14 and #15 as shown in the provided diagram. If that's what you're speaking of, then yes we do offer that nut and…

view full answer...

Answer 3

There are a few repair parts for the Blackhawk 2 tow bar, #RM-422, but not all components can be repaired. I have included the replacement parts we have available below. - Roadmaster Square Plug #RM-200140-40 - Replacement Base Pins with Chains and…

view full answer...

Answer 4

Hey Paul, great to hear from you! Yes, the Replacement Hitch Shank #RM63GR is the part of the tow bar that fits into the hitch receiver on the towing vehicle (see highlighted yellow part of attached BlackHawk 2 All-Terrain #RM-422 photo).

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Release Latch Recommendation for Roadmaster Blackhawk 2 Tow Bar

Product Page this Question was Asked From

Continue Researching