What Size are the Set Screws on Ram Gooseneck Trailer Coupler # GCPN-25008

Question

Question:

Can you tell what size of bolts are on the GCPN-25008?

asked by: Perry W

0

Expert Reply:

Ram gooseneck coupler # GCPN-25008 has set screws and a 7/8" diameter pin. The set screws are 3/4"-10 x 2-1/2". It is recommended to use a large crescent wrench to adjust the set screws since they have a square head instead of a hex head like a regular bolt. There is a replacement set available as # SS-34103-BT. The matching set screw nuts are # SS-34103-NT.

expert reply by: Michael H

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 3

The 1/2"-20 lug nut that I would recommend is the Kodiak Trailer Wheel Lug Nut #KALN1375S. The reason I recommend this lug nut is because it is a one piece, stainless steel design. So it is going to be the most durable and allow you to use…

view full answer...

Answer 4

Hello Danny, Does that mean that your trailer is bigger than all the others, just like everything else in Texas..... bad joke, I know. I have not heard of any issues with the Texas Pride and not being able to use the Demco eZ-Latch Gooseneck Coupler…

view full answer...

Answer 5

The correct front mount trailer hitch for your 2000 Chevrolet Silverado 2500 LS will be dependent on if you have a 2WD or 4WD model. If you have a 2WD then you will want to use the Curt Front Mount Trailer Hitch Receiver part #31043 but if you have a…

view full answer...

Answer 6

For a front hitch that fits your 2002 GMC Sierra 3500HD chassis the Draw Tite front hitch part #65028 is the correct fit. The #31043 does not fit your truck.

view full answer...

Answer 7

Hey Matt, we have a topper from Fas-Top that fits the 8 foot long bed versions of the 2024 Ford F-350 with the part #FT63EV but the part #FT84MV only fits the short bed trucks and would not work for you. The Solo is just the topper whereas the…

view full answer...

Answer 8

Hello Joseph, thanks for reaching out. Our etrailer Base Plate #e98948 will fit the 2023 Jeep Gladiator with the standard plastic factory bumper, but there would be no way to adapt this to your tow bar. Your best option here will be to use the Curt…

view full answer...

Answer 9

The Replacement 42" Cable for Breakaway Switch from Bright Way Group, #3802350, will fit most models of ESCO break away switches. If you don't want to take a chance on it not fitting, I would instead recommend replacing the switch with part…

view full answer...

Answer 10

As long as your dual wheel has a flat surface where the Flange Wheel Nut #95188 would rest against, like what the Dexstar Dual Wheel #AM20790 has, then you would use this flange wheel nut in the place of a nut with a 90 degree cone. Attached is a…

view full answer...

Answer 11

Dexter recommends a SAE 90, SAE 80W-90 or SAE 75W-90 oil to be used. I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE as it is a synthetic 90 weight oil that helps reduce friction and to keep bearings cool. Since your cap was…

view full answer...

Answer 12

I went out to the warehouse and measured the Gooseneck Coupler Handle #GCPN-HD and measured 8 1/2" overall, 3 1/4" for an overall height, 2 1/2" for an inside measurement, and is 12.95 mm (.5") thick. I've attached a diagram…

view full answer...

What Size are the Set Screws on Ram Gooseneck Trailer Coupler # GCPN-25008

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching