What is the Mounting Bolt Pattern for Electric Trailer Brake Assembly # 23-429

Question

Question:

Can i get the measurement to make sure matches my flange Im having troubles finding the right brake assembly thank you

asked by: Nathan

0

Expert Reply:

Trailer brake assembly # 23-429 has mounting holes that are 3-5/8" apart on center side to side, 4-3/8" on center top to bottom, and 5 inches on center diagonally. The matching left hand side assembly is # 23-428.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Dexter Electric Trailer Brake Assembly #23-429 & #23-428 have a center opening of 3-7/8" for fitting on the axle tube. It will mount to bolt holes that are 3-5/8" spread left to right and 4-3/8" top to bottom. I have included…

view full answer...

Answer 2

There is a size difference between the brake assemblies that fit 7k axles and 8k axles so you would not be able to use 7k assemblies on an 8k axle. You'll have to measure your current assemblies do determine which kit you'd need:…

view full answer...

Answer 3

Yes, the Dexter Electric Trailer Brake Kit #DX32QR is the correct replacement brakes for your Big Tex with Dexter D80N Axles.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

What is the Mounting Bolt Pattern for Electric Trailer Brake Assembly # 23-429

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching