Coupler Locks That Can be Keyed Alike

Question

Question:

i would like to buy four of the traler pin locks all keyed the same is that option

asked by: Zach M

0

Expert Reply:

For coupler locks that can be keyed alike you can use our etrailer.com Stainless Steel Trailer Coupler Lock # e98885. You only need to select the "Keyed Alike" option from the dropdown menu on the product page and the quantity you want. I've added links to video reviews of this lock for you to take a look at.

expert reply by: Kyle S

0

Answer 1

Yes, the best way to deter thieves with bolt cutters is to use a very short pin lock in the latch part #e98885. This etrailer.com stainless steel coupler lock only measures a 1/2" span and will not give the thief room to use the bolt cutters to…

view full answer...

Answer 2

I went out into our warehouse and pulled a Stainless Steel Trailer Coupler Lock #e98885 and found that the overall diameter of the unit is 1-1/8 inches.

view full answer...

Answer 3

As you probably already know, fenders can mount to trailers in any number of ways so there is no set method of installation. Most of the time you will need to attach them with brackets like #PF775-BKT-2 and use your own hardware to install to the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Coupler Locks That Can be Keyed Alike

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching