Does the RhinoFLEX Rhino Blaster Pro Adapter # CAM39085 Install on Standard 3" Fitting

Question

Question:

Is this the standard 3" pipe size?

asked by: Troy

0

Expert Reply:

The RhinoFLEX Rhino Blaster Pro Adapter # CAM39085 that you referenced is an easy, tool-free installation that has a 3" bayonet fitting for your RV's holding tank an 3" lug fitting for your sewer hose's bayonet fitting.

If you check out the attached review video you can see this process demonstrated.

expert reply by: Jon G

0

Answer 1

Yes, you can remove the rivets and use some self tapping screws to secure the #LCV000334398 and complete the installation. If you watch the video attached below starting at the 10 minute mark you will see where they used the #FA1131822 to finish…

view full answer...

Answer 2

I spoke to my contact at Lippert and he told me the Replacement Cover for Solera Awnings - Idler Head - Front Cover - Black #LC643923 would be the correct replacement cover for your power awnings. If you need the motor side cover, that will be the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Does the RhinoFLEX Rhino Blaster Pro Adapter # CAM39085 Install on Standard 3" Fitting

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching