Parts Needed to Add Solera Awning to Trailer

Question

Question:

Does this awning come complete with all mounting hardware? There is nothing on the side of my trailer. Thanks,

asked by: Kent N

0

Expert Reply:

The Solera Awnings like the part # LCV000211518 do come with the awning rail that mounts to the side of your trailer. They used to not be included but they recently started including the rail.

In addition you will need:

Solera Manual Pull Style Awning Drive Head # LC272067
Solera Manual Crank Style Awning Idler Head # LC273479
Solera Manual Awning Pull Strap # LC292794
Solera Standard Flat Awning Support Arm 69 inches # LC281154

expert reply by: Jameson C

0

Answer 1

In order to remove the old retaining pin from the drive pin on your Solera awning you will first need to remove the cover. The Drive Head Retaining Clip #LC266137 slides into the groove on the Drive Head Pin for Solera Power RV Awnings #LC266141. You…

view full answer...

Answer 2

Based on the pictures you definitely need the awning support arm #LC281154. I can't tell in that other photo if the pin is bent or damaged, or just barely hanging in there. I'm also not sure if your idler head and roller endcap are ok or not…

view full answer...

Answer 3

The inner arm for your Lippert Solera Awning is not available for replacement, so to replace your inner arm you'd have to purchase the entire assembly. We have plenty of options for you to check out and may work great for you. If you have short…

view full answer...

Answer 4

There is a solution for you, though the upper pitch arm you referenced is not available as an individual piece. It will come with a support arm assembly, and the one you need is going to depend on the length of the wall-mount extrusion from top to…

view full answer...

Answer 5

I was able to have the Replacement Head Pin for Solera Power Awning Gear Drive Head #LC93FR pulled from our warehouse and got the following dimensions for you. Overall length: 4-1/16" Length between notches: 1" Distance from pin hole to end…

view full answer...

Answer 6

The Replacement Head Pin for Solera Power Awning Gear Drive Head #LC93FR is the correct head pin replacement for the Solera Power Awning Drive Head #LC273478. If you have the Solera Power Awning Plain Drive Head #LC266146 then the correct replacement…

view full answer...

Answer 7

An alternative version to the Replacement Drive Head Pin for Solera Power RV Awnings #LC93FR (Regal Style) is the part #LC266141 which is for the Plain Style. This has a flattened end on both ends of the pin which sounds like what you're looking…

view full answer...

Answer 8

If you are referring to the head pin then yes we do have this available as the Replacement Head Pin for Solera Power Awning Gear Drive Head part #LC266141. That said, you would also want two Replacement Retaining Clips part #LC266137 and one…

view full answer...

Answer 9

It sounds like you have a Solera Power Awning on your Salem Hemisphere. Based on what you have described either the drive pin is broken/sheared or a gear is broken inside the drive head. I recommend checking both to see if you can confirm this is the…

view full answer...

Answer 10

The pin you need for your Solera Power Awning Drive Head is part #LC266141. The Replacement Drive Head Gear Kit #LC353964 does not include the pin so you need to use the part I mentioned above. Please note that when I reached out to my contact at…

view full answer...

Answer 11

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Answer 12

Looks like you are in need of the replacement retaining clip for the Solera drive head part #LC266137.

view full answer...

Parts Needed to Add Solera Awning to Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching