Recommended Trailer Hitch Receiver for a 2007 MazdaSPEED 3

Question

Question:

Need a hitch for my 2007 mazdaspeed 3.in the comments, they say this one would work if I just remove my rear bumper. ty

asked by: Luke

0

Expert Reply:

We have 2 trailer hitch receiver options for the 2007 Mazda 3 which include the Curt # C11386 and the Draw-Tite # 24816. The Curt option is not a confirmed fit for the MazdaSPEED that you have, but the Draw-Tite will fit.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 10

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Answer 11

We have 2 trailer hitch receiver options for the 2007 Mazda 3 which include the Curt #C11386 and the Draw-Tite #24816. The Curt option is not a confirmed fit for the MazdaSPEED that you have, but the Draw-Tite will fit.

view full answer...

Recommended Trailer Hitch Receiver for a 2007 MazdaSPEED 3

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching