Recommended Trailer Wiring Harness on a 2014 Audi A6
Published 12/21/2016
Products Featured in This Question
Question:
I have a 2014 Audi A6 with AWD and did not see a custom wiring kit for adding a trailer hitch light package. Is there a problem with installing these systems on an A6. What is the recommended wiring package to use for this vehicle.
asked by: David B
Expert Reply:
We do not carry a custom wiring kit for your 2014 Audi A6. I recommend using the ZCI Circuit Protected Wiring Harness # 119250KIT on your Audi. This is a universal harness that does not require any splicing. Instead, it uses sensors that clamp around the car's wires to read the current that travels through the wire. I've attached an install video for you to take a look at.
If you don't already have a htich reciever on your A6, the Curt # C11423 is a Class I receiver confirmed to fit. It has a towing capacity of 2,000 pounds with a maximum tongue weight rated of 200 pounds. As always you should check your owner's manual to verify your vehicle doesn't have any restrictions on towing.
For a ball mount, an option is the Curt # C45521 that has a rise of 2-5/8 inches or a drop of 3-1/4 inches. Then either # A-82 for a 2 inch hitch ball or # A-80 for a 1-7/8 inch ball. Finally, # F-4 will work for a pin and clip.
Product Page this Question was Asked From
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Converter
- Universal Fit
- 4 Flat
- Plug and Lead
- Plug-In
- Hidden
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Curt Powered Tail Light Converter Set Up - 2021 Audi Q7
- Shop: ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Installation: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector on a 2011 Audi A4
- Video: Mount: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector on a 2008 Audi Q7
- Video: Trailer Wiring Harness Installation - 2013 BMW X5
- Shop: Trailer Hitch
- Video: Set up: Curt Trailer Hitch Receiver on a 2012 Audi A6
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer hitch ball mount
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Gooseneck Hitch
- Search Results: hitch bike racks
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
on Custom Fit Vehicle Wiring
