How Does the Gooseneck Hitch Ball of a B and W Turnover Ball Release from a Hitch

Question

Question:

is there a pin holding the ball in when it is overturned upside down in storage? How do I remove it ? I yanked and yanked and it does not come out. not rusted in, but looks like a pin is going across it.

asked by: Randy

0

Expert Reply:

There will be a lever underneath the rear wheel well of your truck that will need to be pulled out so that the ball of the hitch can release.

I attached a picture of what the lever will look like.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thanks for the picture! That is exactly what I need to confirm what pin box your Forest River Shasta Phoenix 28RB has. I just spoke with my rep at Lippert and you have a 1621 pin box with an 18,000 lbs capacity. You will want the Gen-Y Hitch 5th…

view full answer...

Answer 2

Though there is not a separate lock available for the latch pin handle of the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1108 that fits your 2002 Ford F-250, it would not be able to be removed by a teen or young kid. If you take a…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hello Gary. For your 2024 Chevy Silverado 2500 HD with short bed it is recommended to have a sliding hitch to ensure that you can get around those really tight turns without damaging the cab of your truck. For a Curt sliding hitch I would recommend…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 12

Yes, we do. What you are describing sounds like the Inner Frame Brackets for Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Hitch item #RP27FR. I have attached a picture below. These come welded to the frame exactly where you…

view full answer...

How Does the Gooseneck Hitch Ball of a B and W Turnover Ball Release from a Hitch

Product Page this Question was Asked From

Continue Researching