2012 Yacht Club WC224 Trailer Fender Recommendation

Question

Question:

need to get passenger fender for 2012 wc224 yacht club traler

asked by: Shaun C

0

Expert Reply:

I was able to pull up your 2012 WC224 trailer and found that it has 13 inch trailer wheels and has a fender that looks identical to the part # F008583. This fender would work well for you and would be what we recommend.

I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

There aren't fenders available that have cutouts for side marker lights, but there is a way to add lights to the CE Smith Single Axle Trailer Fenders with Top and Side Steps #CE19502-2. You could very carefully cut the fenders because they are…

view full answer...

Answer 2

Fulton Single Axle Trailer Fender with Top and Side Steps - Black Plastic - 13" Wheels - Qty 1 #F008583 will work for you 2010 WC224 YachtClub Jetski trailer. We have many different light options like the Wesbar Waterproof Clearance/Side Marker…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

2012 Yacht Club WC224 Trailer Fender Recommendation

Featured Help Information

Miscellaneous Media

Continue Researching