Location of Brake Controller Port on 2010 Dodge Ram For Tekonsha Brake Control Adapter, # 3021-P,

Question

Question:

where is the port for the brake controller on a 2010 dodge ram 1500 anyone have a photo

asked by: john g

0

Expert Reply:

The brake controller harness is located under the dash on the drivers side, just left of the steering column, and near the emergency brake pedal. See picture at the right.

I am sending a link on the installation instructions on a 2010 Dodge Ram. It shows the location of the factory port, for the plug in of the Tekonsha Brake Control Adapter - 2010 Dodge, # 3021-P, on your 2010 Dodge Ram 1500.

expert reply by: Jeff D

0

click to enlarge

Answer 1

For a 2010 Dodge Ram 1500 with a 7-way there is a port under the dash that will be used for the install of a brake controller. The install harness part #3021-P is the harness to use. The plug you are looking for is a white, square connector above the…

view full answer...

Answer 2

It's not uncommon for a tandem axle trailer to have brakes on only one axle. Typically for utility trailers which have more weight towards the front the front axle is the one that will have the brakes and trailers like boat trailers which carry…

view full answer...

Answer 3

I spoke to Tekonsha about finding the exact location for the brake controller on your truck and they told me that for your 2019 Dodge Ram 1500 "the connector is behind the area in the attached picture and from what we’ve been told you can reach…

view full answer...

Answer 4

When we install brake controllers on the newer Rams, 2015 to present, we mount them on the bottom of the dash to the right of the steering wheel. That seems to be the best place for it. I have linked some videos that show brake controller…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Location of Brake Controller Port on 2010 Dodge Ram For Tekonsha Brake Control Adapter, # 3021-P,

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching