Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
Part Numbers: C84VV,C51322
Retail:$156.17
Our Price: $120.57
You Save: $35.60
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
part number: C84VV
An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity.
Features:
- Brake controller activates trailer brakes with preset intensity
- Adjustable power output control lets you select the amount of braking force
- Rocker switches located on left front of module for easy access
- 10 Gain settings and 9 load settings allow you to adapt to various driving conditions
- Select a higher setting for harder braking and lower for more gradual braking
- Pinch-trigger manual override is within easy reach for controlling trailer sway or stopping in emergencies
- Simple LED display shows the amount of power output
- Self-diagnostics monitor trailer connection and check for shorts
- LCD display shows power adjustments in 0.5 increments
- Brightness is adjustable for optimal visibility
- Auto-sleep mode prevents battery drain after 5 minutes of idle time
- Quick and easy installation with no mounting restrictions
- No need to mount level - install anywhere at any angle
- Included mounting bracket and hardware designed to hold the brake controller flush against the dash
- Plug-in, vehicle-specific brake control adapter (sold separately) available for select vehicles to reduce installation time
Specs:
- Application: trailers with up to 4 axles (8 brake assemblies)
- Compatible with low-volt, PWM, ABS, cruise control, and electric-over-hydraulic trailer brakes
- Dimensions: 4" long x 3-1/8" wide x 1" tall
- Limited lifetime warranty
Gain Adjustment
Gain control lets you set the maximum amount of power that will be applied to your trailer's brakes, adjusting in increments of 0.5. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to go as high as you can without the trailer brakes locking up. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes. To get more power to your brakes, press the upper orange rocker switch. To decrease the gain, press the lower switch. When you make your adjustment, the gain setting will show on the LED screen for 10 seconds as a series of bars and then go into sleep mode.
Load Control
Once you have the gain set, you can fine-tune your braking by adjusting the load control on a scale of 1 to 9. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. Load control can get the braking power to your trailer faster and with more intensity so that it doesn't push your tow vehicle forward. If your vehicle takes too long to come to a stop, increase the setting by pressing the upper black rocker switch. If it stops too abruptly, decrease the setting by pressing the lower switch. You can alter the setting to suit your driving preferences or to improve handling based on changing road conditions or varied trailer loads.
Pinch-Trigger Manual Override
The Discovery comes with a easy-to-reach, pinch-trigger manual override, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push in the trigger. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
LED Display
The LED display on the Discovery is large and easy to read at a glance. It will show you what setting the brake controller is on as well as give you information for troubleshooting. You can adjust the screen brightness or trigger night mode so it won't glare obnoxiously on your dash. Press the control button to cycle through the different modes.
Quick Installation
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, so long as you can still easily access the controller and the manual override. The included bracket is designed to mount the brake controller flush to the dash so it takes up almost no space at all.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Time-Delayed Braking
The Curt Discovery comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the Discovery. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. Both the amount of braking power (gain) and rate of application (load) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
51126 Curt Discovery NEXT Time Delay Trailer Brake Control - 1 to 4 Axles
Replaces Curt 51120
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
part number: C51322
Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.
Features:
- Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
- No cutting or splicing required
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible with time-delayed and proportional brake controllers from Curt
- Brake controller must have built-in plug for adapter to connect - will not work on controllers with pigtail wiring harnesses
- 2' Long, 12-gauge wires have protective covering to deter damage
- Limited 1-year warranty
Installation of Curt Brake Controller Adapter
To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. When this is done, a port is installed at your dash so that you can easily plug in a brake controller.
This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness is located beneath the dash, near the center console.
No hardwiring is required to install this adapter. After you plug it into the factory port, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.
51322 Curt Quick Plug Brake Control Adaptor Harness
Item # C51322
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Defective
- Product did not meet expectations
- Alternate product found
Customer Reviews
Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed - C84VV
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In - C51322
Average Customer Rating: 4.8 out of 5 stars (281 Customer Reviews)
An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity. Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.by: Garth 02/23/2024
1997 Ford F-350 Super Duty
They are the best at what they do. They found the parts I needed and got them to me the next day. I appreciate the dedication to their customers. This product worked for my 1997 Ford F350 with the factory-installed tow package.
by: Eric P. Foxboro,MA07/16/2017
Everything was as described. Easy easy installation in 10 minutes. Not the top of the line controller but it's all I need. Very fast shipping as well. Couldn't be more happy with etrailer. I will be purchasing my fifth through etrailer soon!
by: Dave K / NHS08/28/2017
Great job came on time. Installed easily. Works great. Better still is the service from etrailer. New what I needed for my truck. Deserves repeat business
by: John R05/24/2024
Took about 10 minutes to install. Have not made all the adjustments yet, but is easy to understand.
by: Nicholas06/27/2018
Plugged right in to my expeditions factory plug quick easy install.
by: Jerry 04/25/2024
Tested . Work fine and advertised
by: Diego 02/11/2023
Ford F-250 Super Duty
PERFECT. The etrailer.com employee (Roger R) that assisted me on my phone in order was fast, and efficient. He looked up my truck (2004 f250 diesel 4x4), and assisted me in ordering the exactly correct harness for my application. Plug and play. Thanks.
by: Matthew L.07/12/2017
Ford
Installation pics on my Ford F-150
by: mike R.07/29/2013
Excellent. Perfect fit, exactly what was needed. Connected the Curt C51110 Brake control to factory wiring. Only thing that could make it better is if it came with someone to plug it in for me and save me 10 seconds.
by: Ethan 03/15/2024
excellent service and delivery.
by: Lawrence 02/07/2024
straight forward install, works as inte nded.
by: Stuart 03/27/2024
Exactly what I ordered and expected.
by: Thomas 02/12/2024
Worked perfectly
by: Adam 02/09/2024
Wonderful product as well as wonderful customer service
by: Joe04/13/2021
We purchased our new Ford Explorer with the towing package but the dealership said it didn't come with a trailer brake controller and nothing was made for our SUV so we would have to get an aftermarket controller and have them run the wiring. After looking online I found a video on etrailer.com and it was just as easy as the video to install, the hardest part was finding the Ford plug under the dash, very happy with this product and ready to haul our RV everywhere.
by: Jay 05/10/2020
2017 Land Rover Evoque
Made installation in a Land Rover Discovery Sport a breeze! Note: This option isn’t listed on either Curt or eTrailer, but it is absolutely an option if you have the factory installed OEM trailer tow package. Your factory tow package must be dealer activated in your vehicle’s software to use the quick connect harness shown here.
Total plug and play. Zero cutting, splicing or tapping required! Fantastic.
TIP: Select your model year and Land Rover Evoque (Shares the same chassis and tow electrics as the Discovery Sport) if you want the right part numbers for your quick connect options.
by: Chris 11/09/2023
Works great in my 2000 f250
by: Nicholas08/01/2019
Made installation a snap. Just mount the break controller, plug one end into the vehicle's factory plug and the other end into the break controller.
Nicholas
8/3/2020
Still working great
by: Sidney 09/21/2023
Like its compact size and simple operat ion.
by: Dusten09/21/2023
Very helpful, knowledgeable and friendl y!
by: RMT05/20/2014
2003 FordF-150
Plugged right in to my 2003 Ford F-150, and other end into the Curt Venturer brake controller. Worked great.
Rmt
5/20/2015
so far so good. no issues.
by: ZY11/11/2021
Nice trailer brake. Works as it should.
by: Kelly11/08/2016
2004 FordF-150
This is well worth the money. The cord ends appear to be high quality and fit the wiring connectors on the truck and brake controller perfectly. It makes hooking up your new Curt brake controller as easy as plugging in a cord. The only way to make this any easier is to have someone do it for you. The hardest part of the whole installation was finding the factory connector to plug this cord into. Hint: On my 2004 Ford F150, the brake controller connector was just above the factory diagnostic port underneath the dash.
by: JB from MT10/09/2014
2010 Ford Expedition
This cable made the job very easy. took 10 minutes to plug in and mount with Curt Venturer Brake Controller. Very inexpensive solution. This is an old vehicle (2001 Expedition) and didn't want to put a lot of money into a brake controller setup. These parts and directions from the website made it quick, easy and inexpensive. I have not towed with the controller yet.
25
281
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- Brake Stoplamp Switch Wire Color For Brake Controller Install on 2016 Ford F150
- You'll be looking for a purple and white wire, but if you're wanting to install a brake controller there is a plug and play option that would require no cutting or splicing.
If you look at the installation video I've linked for you, you can see that the brake controller connector is located behind the dash, all you'll need is the correct wiring harness to connect the controller and the vehicle and you'll be good to go. If you're using a Curt brake controller like the # C84VV, you would
view full answer... - Brake Controller Recommendation for a 2005 American Revolution LE Motorhome
- I'd be more than happy to help out!
I recommend using the Curt Discovery NEXT Trailer Brake Controller # C84VV with the Universal Wiring Adapter # C51515 for your 2005 American Revolution LE motorhome. The Discovery NEXT is a time-delayed controller so it sends pre-determined power back to your trailer brakes instead of activating them proportionally.
I couldn't find a pinout or connector style that matches exactly with your motorhome so you'll need to splice in your connections by
view full answer... - Curt Discovery Trailer Brake Controller # C84VV Displays Only a Red Dot After Installation
- If your Curt Discovery Trailer Brake Controller # C84VV displays only a red dot when you do NOT have a trailer connected then this indicates that the controller's red (input signal) wire is connected to the wrong side of the brake light switch. This red wire should connect to the COLD side of the switch that has power only when you press the brake pedal.
If your Discovery displays the red dot when you DO have a trailer connected then this usually indicates a problem in the trailer brake
view full answer... - Why Is Stoplight Circuit Difficult to Find on 2017 Ram 1500 For Installing Brake Controller
- Your generation of Ram truck uses a powernet style of wiring at the brake switch wiring which means the voltage will actually read lower than what a 12 volt circuit tester is going to show. Also if you are trying to hardwire a controller you are going to have issues as we've found that if you don't use a harness designed specifically for your truck's wiring setup you may damage the vehicle.
So to install the Curt Discovery part # C84VV you have to use the vehicle specific install harness
view full answer... - Installing A Brake Controller in a 2008 GMC Yukon XL Without Plug and Play Adapter Harness
- On your 2008 GMC Yukon XL, there is not a direct plug and play harness for a brake controller. This is because no plug is present under the dash, however the needed wires are already run so it is a simple install. You will connect the brake controller wiring with the vehicle wiring already present under the dash with butt connectors like # 05731-5.
The Curt Discovery Timed Delay Brake Controller # C84VV gives you the option to either cut the connector off the brake controller or use
view full answer... - Troubleshooting No Power on Blue Wire After Installing Curt Discovery Brake Controller
- The issue you're describing likely has to do with the red brake input wire coming from the Curt Discovery Brake Controller # C84VV and corresponding harness # C51515.
You will want to make sure that this red wire is connected to the cold side of the brake light switch behind the Suburban's brake pedal. This is the wire that ONLY gets power when the brake pedal is depressed and no power with any other function. I recommend using a circuit tester like # PTW2993 to verify you have found
view full answer... - Troubleshooting Curt Discovery Brake Controller Issues on Ram 1500
- The Curt Discovery Brake Controller # C84VV is a time-delay type that is intended to send out a pre-determined amount of braking power after you have applied the vehicle brakes. The other type that is often preferred is the proportional type that will actually sense the amount of braking force in the tow vehicle and send a proportional amount of braking power to the trailer, without a time delay.
Based on the symptoms you described I think the issue could be with the wiring on the trailer.
view full answer... - Will Curt Discovery Brake Controller Work With a 2003 Cadillac Escalade?
- The Curt Discovery Trailer Brake Controller, # C84VV, is a fit on your 2003 Cadillac Escalade, though it will require the use of the Curt Custom Wiring Adapter, # C51352.
This product simply plugs into the port that is located in the junction box that is under your dash to the left of your steering column. The exact spot it plugs in will be on the top row, second slot from the left.
view full answer... - Wiring Harness Needed to Plug Curt Brake Controller into a 2006 Ford F-150
- The Curt brake controller # C84VV can plug directly into your 2006 Ford F-150 using the proper wiring harness, # C51322. This harness is sold separately. I have included a link to a video to the right that shows where the connection point is on your truck. The brake controller and harness are different in the video but they plug into the same place on the truck.
view full answer... - Help! Curt Discovery Trailer Brake Controller # C84VV Only Shows Decimal When Brake is Applied
- Since the Curt Discovery Trailer Brake Controller, # C84VV, is still displaying the decimal when the trailer is connected, the controller is not sensing a connection with the trailer brakes. In this case the issue is most likely related to a wiring problem or brake magnet problem. I would start by making sure that there isn't any corrosion in either connector. Next, I recommend using a circuit tester like part # PTW2993, to make sure that you have power on the brake controller output pin
view full answer... - Adapter Needed to Install the Curt Discovery on a 2005 Ford F-150
- To install the Curt Discovery Trailer Brake Controller # C84VV on your 2005 Ford F-150 you will need the Curt Custom Wiring Adapter # C51322.
This connector will be found under the dash on your driver side. I have attached a video of this adapter being used to install the Curt Venturer on a 2004 F-250 that you can use as a reference.
view full answer... - How Does Brake Controller Install in 2012 Ford F-150
- When installing the Curt Discover part # C84VV with the harness for your 2012 Ford F-150, part # C51436 all you'd have to do is plug in the controller and harness and you'd be set if you have the factory 7-way like it sounds like you do. It's really a pretty simple install.
Otherwise you'd need a 4-way to 7-way adapter like part # 37185 and you'd have to run the wire from the truck's frame rail to the adapter and you'd be set. See attached picture for more info on that.
view full answer... - Curt Discovery Brake Controller Display Flashes with Left Turn Signal
- It could be a wiring issue. Specifically, it is likely related to the brake controller red wire. If that wire is not attached to the correct circuit, it can cause some strange things to happen. The red wire needs to be connected to a brake switch wire that only has power when the brake pedal is pressed.
If that same wire has power, then the headlights or a turn signal are on then it is not the correct wire. I have heard that the correct brake switch wire is the white wire so use a circuit
view full answer... - Does Dealer Need to Turn on Aftermarket Brake Controller in a 2015 Ford F-150?
- There will be no need for you to go to take your 2015 Ford F-150 to the dealer to have them turn on an aftermarket brake controller. The brake controller I recommend that you need only an adapter for is the Curt Discovery # C84VV.
Since you already have the factory tow package, just use the Plug-In Wiring Adapter # C51436.
Plug one side into the brake controller and the other side into the wiring on your F-150 and you are done.
view full answer... - No Brake Output on Curt Discovery Trailer Brake Controller
- If you have power going into the Curt Discovery Trailer Brake Controller part # C84VV on the black wire, the ground has good continuity, and you have power on the red wire while the pedal is pressed and there is no output on the blue wire then it's safe to say the controller is bad and will need to be replaced. That said, please make sure you are checking the wires directly behind the controller so you can rule out any other issues down the line. The Curt Discovery is a timed delay controller
view full answer... - Wiring Adapter for Installing Curt Discovery Brake Controller on 2014 Ford Explorer
- To install the Curt Discovery # C84VV brake controller on your 2014 Explorer, you'll need the Curt wiring adapter, part # C51322.
view full answer... - Compatibility of Curt Discovery Brake Controller With 2010 Chevy Silverado
- Brake controllers are not vehicle specific. The # C84VV Curt Discovery brake controller is compatible with your 2010 Silverado. You'll also need the Universal Curt Brake Controller Pigtail, part # C51515. The pigtail wire will connect directly to the tow package wiring located under the dash between the steering column and the emergency brake pedal. Look for a bundle of wires with a white tag hanging from it. The wires of the pigtail will connect to the tow package wiring as follows:
Red
view full answer... - Curt Brake Controller and Wiring Harness for a 2015 Ford F-150
- For a Curt Discovery brake controller # C84VV you will need wiring harness # C51436 for your 2015 Ford F-150.
view full answer... - How to Install Curt Discovery Brake Controller in 2008 Ford F-150 With Factory 7-Way
- The Curt Discovery brake controller part # C84VV that you referenced can easily fit your 2008 Ford F-150 with the factory 7-way by using custom install harness part # C51322.
This plugs into the brake controller install port under the dash of your truck and then into the back of the controller and you're set.
view full answer... - Wiring Needed to Install Curt Discovery Brake Controller on 2005 Toyota Tacoma
- There are a few different ways to connect the Curt Discovery Trailer Brake Controller # C84VV to your 2005 Toyota Tacoma and it just depends on whether you have the tow package or not. I've listed what you'll need in both scenarios below.
With Tow Package
Curt Discovery - # C84VV
Wiring Adapter - # C51362
Without Tow Package
Curt Discovery - # C84VV
Pigtail - # C51515
4-Way Wiring - # C55513 (if you don't already have one)
Wiring Upgrade Kit - # ETBC7 (if you don't already have
view full answer... - Parts Needed to Install a Brake Controller in a 1994 Ford Bronco
- Yes, to install a Curt brake controller like the TriFlex part # C24VV in your 1994 Ford Bronco all you would need is the correct brake controller install harness part # C51322 that you referenced.
Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port beneath your vehicle's dash.
view full answer... - Where is the Wiring Harness for a Curt Custom Wiring Adapter # C51322 on a 1996 Ford F-150?
- According to the instructional manual of the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51322, the harness on your 1996 Ford F-150 is located underneath the dashboard near the center console. I went ahead and attached a photo to this answer that I highlighted that shows the location.
view full answer... - Economically Priced Proportional Brake Controller Recommendation for a 2004 Ford F-150
- For a great brake controller at a great price I would recommend the Curt Triflex Brake Controller part # C24VV. This is a proportional brake controller that will sense how much braking power the tow vehicle is applying and will proportionately apply the trailer brakes to slow the trailer down in a smooth, effective manner.
To install the brake controller all you need is the correct install harness which would be the part # C51322. Check out the link to the install video I attached as well.
view full answer... - Curt Brake Controller and Wiring Adapter for 2015 Forest River FR3 30DS on Ford F-53 Chassis
- To use the Curt Assure Brake Controller # C49UR with your 2015 Forest River FR3 30DS, which was built on a Ford F-53 chassis, you will need the Wiring Adapter # C51322.
The other part you will need is Adapter # 37185 to give you 7-way on your motorhome.
view full answer... - Brake Controller and Install Harness for a 2013 Ford Explorer
- For installing the Tri-Flex brake controller part # C24VV in a 2013 Ford Explorer the correct install harness is the part # C51322.
I confirmed this with Curt as a fit for your vehicle. he Ford Explorer and Mercury Mountaineer have 6-pin connectors behind the glove box on the passenger's side that this connector will install into.
view full answer... - Will Brake Controller Plug-In Adapter C51322 Fit 2004 Ford Expedition And 2004 Ford E-350
- The Curt Custom Wiring Adapter, part # C51322 is designed to work with the # C74VV brake controller and will fit both of your vehicles if there is a factory trailer connector installed on the vehicle.
If you have a 4-way connector on either vehicle then you will also need part # 37185.
If your E-350 does not have a trailer connector you will first need to install a 4-way connector like part # 18252. You will then need part # ETBC7 to get a 7-way at the back of your vehicle. If there
view full answer... - Wiring Harness for 2013 Thor Challenger With Curt Brake Controller
- For a Curt brake controller, the correct brake controller wiring harness for your 2013 Thor Challenger is the Curt Wiring Adapter # C51322.
view full answer... - Where is the Brake Controller Installation Plug on a 2000 Ford F-250
- The plug you're looking for on your 2000 Ford F-250 is likely located behind some of the wire looms or possibly even tucked away in a nook off to the side when you remove the dash panel, but it will be there somewhere. Once you find this plug you'll be able to use the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51322 to install the Curt Tri-Flex # C74VV. I've linked a few installation videos of brake controllers that use a brake controller adapter plug so
view full answer... - Brake Controller Installed on 2001 Ford Van Causes Turn Signal to Malfunction
- You are using the factory pigtail provided when you purchased the vehicle, not the # C51322, is that correct? If this is the case, the factory pigtail uses a different wire color code than the aftermarket ones, which match up color for color. Before proceeding further, lets make sure you have the pigtail wired correctly to the brake controller. An incorrectly wired harness or pigtail could cause the problem you describe.
Over the years, Ford has made two different factory pigtails, one
view full answer... - Where is Install Connector on 2014 Ford Explorer for Curt Brake Controller
- The correct install harness for a Curt brake controller in a 2014 Ford Explorer is the part # C51322. The harness you are looking for on your vehicle will be under the dash to the center towards the center console.
I attached an install video that shows a different brand controller and harness installed in a 2013 Ford Explorer which will be the exact same process. Around the 10 minute mark is where the connector on the vehicle is found.
view full answer... - Does Curt Brake Controller Install Harness # C51322 Fit 2007 Ford F-150
- The Curt brake controller install harness part # C51322 that you referenced is a confirmed fit for your 2007 Ford F-150.This adapter plugs into the port on your vehicle's built-in brake control wiring harness. For most applications, this harness is located beneath the dash, near the center console.
Most likely the mechanic you brought it to didn't know where to connect it.
This would work well with the proportional Triflex part # C24VV.
view full answer... - Does Curt Brake Controller Install Harness # C51322 Fit 2000 Ford F-53
- Yes, for your 2000 Ford F-53 RV chassis the Curt brake controller install harness part # C51322 is a confirmed fit and would work well.
It would work really well with the Triflex part # C24VV.
view full answer... - Wiring Harness For Curt Brake Controller on 2002 Ford F-350 Super Duty
- Yes the wiring harness for your 2002 Ford F-350 Super Duty is indeed the same Curt brake controllers.
The Curt brake controllers for your truck will use the Curt Wiring Adapter # C51322.
view full answer... - Can Curt Brake Controller Install on 2009 Porsche Cayenne
- For the 2009 Porsche Cayenne you can install a Curt brake controller like the part # C24VV but due to the complex wiring of your vehicle we don't have a specific fit harness for it. I attached a tech bulleting below that details everything that's needed to install a controller as well as a fitguide list for all the controllers that fit your vehicle.
If you had ran your vehicle through our fitguide you'd seen the list of controller and how they need to install. If you searched for brake
view full answer... - Is The Curt Wiring Adapter Compatible w/ Hayes Energize III Trailer Brake Controller For 1996 F-350?
- The Curt Wiring Adapter # C51322 is compatible with the Hayes Energize III+ Trailer Brake Controller # HA81742B. Both the Curt and Hayes Adapters # HA81783-HBC utilize the same connectors allowing you to use it on your 1996 Ford F-350.
view full answer... - Brake Controller Wiring Harness for a Curt Brake Controller on a 2014 Ram 1500
- If you are using a Curt trailer brake controller then for your 2014 Ram 1500 you will need harness # C51453. Harness # C51322 fits Ford, Land Rover, Lincoln, and Mercury vehicles. The new Rams have a unique multiplex wiring system called Powernet. Because of this new design it requires a special brake controller harness, # C51453, which will allow the Curt brake controller to function properly.
view full answer... - Recommended Curt Wiring Harness for Brake Controller on 2003 Ford Explorer
- To make your Curt Venturer Brake Controller # C74VV able to function with your factory tow package you simply need the wiring adapter harness. For your 2003 Ford Explorer Eddie Bauer edition, that wiring adapter is the Curt Custom Wiring Adapter for Trailer Brake Controllers # C51322. On an Explorer that harness is behind the glove box on the passenger's side.
view full answer...
Info for these parts were:
Edited by:
Leah B
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Written by:
Lindsey S
Video by:
Joshua S
Video by:
Jonathan Y
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
Test Fit:
Ryan G
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike R.
1/28/2015
The products worked great up until about a few weeks ago Thats when I sold the truck where the items were installed. lol. Really though, I very much liked how the products listed and purchased from etrailer.com were easy to find, fit exactly as described, and performed as needed. etrailer.com is always one of the first places I look when searching for items for my new truck.