The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Easy place to shop. Fast delivery and great products. Very happy with my purchase.
Ed
Boynton Beach, FL
B and B Molders RV Slide Out Parts for Corners
B and B Molders RV slide out parts keep trim looking right with corner and end caps in square or curved styles for top or bottom locations. Match overall dimensions and center to center hole spacing; sizes include options like 3-1/8" x 3-1/8" with 2-5/8" holes, and colors can be dark brown, black, or charcoal depending on the part. Some corner caps can work on any corner if size and holes align.
Yes, these pieces are sold individually. Plan on ordering one per corner or end as needed. If you're refreshing multiple corners, verify quantity since packages are not bundled. Check the listing for whether it's a single cap, a top rear piece, or a lower cover to match your spot.
Some square corner styles can work on any corner if the size and mounting holes line up. For shaped pieces, choose by location like top rear or bottom front to match your slide. Verify your existing corner's profile—flat with 2 holes versus curved—to avoid orientation problems.
Match the overall size and the hole spacing to your corner. Check whether your cap is flat with 2 holes or has a curved end, and note if it's a top, rear, bottom, or front corner. Measure carefully; we've seen mix-ups like 4-3/8" vs 4-1/2" cause fit issues. If you need specifics, compare the center-to-center hole distance like 1 5/8" or 2-5/8" to your existing part.
Colors include dark brown and charcoal on certain caps. Some end caps are not offered in white; painting the charcoal version with a color-matched spray paint is a practical workaround. Confirm the color listing and compare to your trim so the replacement matches as described.
Filters
