The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Hey Martin, The only difference I'm seeing between the Replacement Motor #TUS24FR and the Replacement Motor #LC125802 is that the TUS24FR has a 9000 RPM rating while the LC125802 has a 440 RPM rating while under load, which jumps up to 500 RPM…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL
RV Slide Out Parts from Tuson RV Brakes
Tuson RV Brakes slide-out parts make straightforward replacements that work great once installed. For the best match, confirm your motor's rpm rating and check the bolt setup—some replacements use a non-threaded pass-through hole with the bolt threading into the actuator tube. If your system matches that style, installation goes smoothly.
Match the motor RPM to your original unit. One option is rated 9000 RPM, while another is 440 RPM under load and 500 RPM unloaded. Check the label on your old motor or your slide-out documentation for its RPM. If your original was a high-speed 9000 RPM unit, choose the 9000 RPM replacement.
Installation and testing are straightforward, and it can work fine right away. Bench test polarity and direction before final mounting. After the first few cycles, recheck fasteners and listen for unusual noise. Durability takes time to confirm, so inspect the mounting and wiring after your initial trips.
The bolt is designed to pass through the motor and thread into the actuator tube. Confirm your setup allows the bolt to engage the actuator tube threads. Reuse the correct bolt length and do not try to cut threads into the motor housing. If the bolt won't start in the tube, realign the motor and tube.
It can be a perfect fit for certain Lippert slide-out drive motors. Verify the RPM rating and mounting style match your original. Confirm that the motor's bolt hole is pass-through and that the bolt actually threads into the actuator tube. Compare connector style and shaft interface before ordering.
Filters
